TPS65180, TPS65181, TPS65180B, TPS65181B
www.ti.com
SLVSA76F –MARCH 2010–REVISED FEBRUARY 2011
PMIC FOR E Ink® Vizplex™ ENABLED ELECTRONIC PAPER DISPLAY
Check for Samples: TPS65180, TPS65181, TPS65180B, TPS65181B
1
FEATURES
•
•
Thermistor Monitoring
2345
•
Single Chip Power Management Solution for
–
–10°C to 85°C Temperature Range
E Ink® Vizplex™ Electronic Paper Displays
–
±1°C Accuracy from 0°C to 50°C
I2C Serial Interface
Slave Address 0x48h (1001000)
•
Generates Positive and Negative Gate and
Source Driver Voltages and Back-Plane Bias
from a Single, Low-Voltage Input Supply
–
•
•
•
Flexible Power-Up Sequencing
•
•
•
3-V to 6-V Input Voltage Range
Interrupt and Sleep Mode Support
Boost Converter for Positive Rail Base
Thermally Enhanced Package for Efficient
Heat Management
(48-Pin 7 mm x 7 mm x 0.9 mm QFN)
Inverting Buck-Boost Converter for Negative
Rail Base
•
Two Adjustable LDOs for Source Driver
Supply
APPLICATIONS
•
Power Supply for Active Matrix E Ink®
Vizplex™ Panels
–
–
LDO1: 15 V, 120 mA (VPOS)
LDO2: –15 V, 120 mA (VNEG)
•
•
•
•
EPD Power Supply
•
•
Accurate Output Voltage Tracking
VPOS - VNEG = ±50 mV
Two Charge Pumps for Gate Driver Supply
E-Book Readers
–
EPSON® S1D13522 (ISIS) Timing Controller
EPSON® S1D13521 (Broadsheet) Timing
Controller
–
–
CP1: 22 V, 10 mA (VDDH)
CP2: –20 V, 12 mA, (VEE)
•
Application Processors With Integrated or
Software Timing Controller ( OMAP™)
•
Adjustable VCOM Driver for Accurate
Panel-Backplane Biasing
–
–
–
–
–0.3 V to –2.5 V
±1.5% Accuracy (±18 mV)
8-Bit Control (11-mV Nominal Step Size)
15-mA Max Integrated Switch
•
Integrated 3.3-V Power Switch for Disabling
System Power Rail
DESCRIPTION
The TPS65180/TPS65181 and TPS65180B/TPS65181B family of devices are single-chip power supplies
designed to for E Ink® Vizplex™ displays used in portable e-reader applications and support panel sizes up to
9.7 inches. Two high efficiency DC/DC boost converters generate ±17-V rails which are boosted to 22 V and –20
V by two change pumps to provide the gate driver supply for the Vizplex™ panel. Two tracking LDOs create the
±15-V source driver supplies which support up to 120-mA of output current. All rails are adjustable through the
I2C interface to accommodate specific panel requirements.
Accurate back-plane biasing is provided by a linear amplifier and can be adjusted either by an external resistor or
the I2C interface. The VCOM driver can source or sink current depending on panel condition. For automatic
VCOM adjustment in production line, VCOM can be set from –0.3 V to –2.5 V with 8-bit control through the serial
interface. The power switch is integrated to isolate VCOM driver from E Ink® panel.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
3
4
5
OMAP is a trademark of Texas Instruments.
Vizplex is a trademark of E Ink Corporation.
E Ink is a registered trademark of E Ink Corporation.
EPSON is a registered trademark of Seiko Epson Corporation.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
© 2010–2011, Texas Instruments Incorporated