TLV320AIC1110
SLAS359 – DECEMBER 2001
PCM CODEC
ꢀ
ꢀ
Capable of Driving 32 Ω Down to a 8-Ω
Speaker
FEATURES
ꢀ
ꢀ
2.7-V to 3.3-V Operation
Programmable Power Down Modes
Designed for Analog and Digital Wireless
ꢀ
Pin Compatible to the TLV320AIC1103 and
TLV320AIC1109 Devices for TQFP Only
Handsets and Telecommunications
Applications
ꢀ
Available in a 32-Pin Thin Quad Flatpack
ꢀ
ꢀ
Two Differential Microphone Inputs
(TQFP) Package and MicroStar Junior
ꢂ
B
G
A
Differential Earphone Outputs and One
Single-Ended Earphone Output
APPLICATIONS
ꢀ
ꢀ
Earphone and Microphone Mute
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Digital Handset
Digital Headset
Programmable Transmit, Receive, and
Sidetone Paths With Extended Gain and
Attenuation Ranges
Cordless Phones
Digital PABX
ꢀ
ꢀ
ꢀ
ꢀ
Programmable for 15-Bit Linear Data or 8-Bit
Companded (µ-law and A-law) Mode
Digital Voice Recording
Supports PCM Clock Rates of 128 kHz and
2.048 MHz
DESCRIPTION
The TLV320AIC1110 provides extended gain and
attenuation flexibility for transmit, receive, and sidetone
paths. A differential earphone output is capable of
driving speaker loads as low as 8 Ω for use in speaker
phone applications. The single tone function on the
TLV320AIC1110 generates a single tone output of up to
8 kHz. The resolution of the DTMF tone is also
selectableto7.8125Hz, 15.625Hz, or31.25Hzthrough
the interface control. The analog switch provides more
control capabilities for voice-band audio processor
(PCM codec).
Pulse Density Modulated (PDM) Buzzer
Output
2
On-Chip I C Bus, Which Provides Simple,
Standard, Two-Wire Serial Interface With
Digital ICs
ꢀ
ꢀ
Dual-Tone Multifrequency (DTMF) and
Single-Tone Generator Capable of up to 8-kHz
Tone With Three Selectable Resolutions of
7.8125 Hz, 15.625 Hz, and 31.25 Hz
2-Channel Auxiliary Multiplexer (MUX) (Analog
ꢁ
Switch)
This device contains circuits to protect its inputs and outputs against damage due to high static voltages or electrostatic fields. These
circuits have been qualified to protect this device against electrostatic discharges (ESD) of up to 2 kV according to MIL-STD-883C,
Method 3015; however, it is advised that precautions be taken to avoid application of any voltage higher than maximum-rated
voltages to these high-impedance circuits. During storage or handling, the device leads should be shorted together or the device
should be placed in conductive foam. In a circuit, unused inputs should always be connected to an appropriated logic voltage level,
preferably either V
or ground. Specific guidelines for handling devices of this type are contained in the publication Guidelines for
CC
Handling Electrostatic-Discharge-Sensitive (ESDS) Devices and Assemblies available from Texas Instruments.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
†
These options are available on some devices. Please see the table of comparison for the last two generations of PCM codecs.
MicroStar Junior is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Copyright 2001, Texas Instruments Incorporated
1
www.ti.com