Ohmite offers the totally encap-
sulated and insulated TO-247
package for low ohmic value
and non-inductive design for
high-frequency and pulsing
applications. Ideal use is for
power supplies. This series is
rated at 100 Watts mounted to
a heat sink.
ꢂ P ꢀ ꢃ ꢄ F ꢄ ꢃ A T ꢄ ꢅ ꢆ ꢂ
Material
TEH100 Series
Resistor: thick film on alumina
Case: high temperature plastic
Lead Material: Tinned Copper
Installation, max. Torque: 0.9 Nm
using an M3 screw and a com-
pression washer
100 Watt Thick Film Power
Resistors for High Frequency and
Pulse Loading Applications
0.610~0.630"
(15.49~16.01mm)
0.185~0.20
(4.69~5.21m
Electrical
Derating: linear, 100% at 25°C to
0% at 175°C
F ꢀ A T ꢁ R ꢀ ꢂ
• 100 Watt power rating at 25°C
case temperature
0.200~0.220"
(5.07~5.59mm)
Resistance range: 0.05Ω to 1MΩ,
other values on request
Resistance tol.: ±1%, ±2%, ±5%,
±10%
Max. working voltage: 350V
Temperature Coefficient:
±50ppm/°C for >10Ω, referenced
to 25°C, ∆R taken at +105°C;
others on request
• Non-inductive performance
• Low thermal resistance
• RoHS compliant design
• TO-247 package configuration
• Single screw mounting simplifies
attach-ment to the heat sink
• A totally molded housing for envi-
romental protection
0.805~0.825"
(20.44~20.96mm)
ø0.139~0.147"
(3.53~3.73mm)
0.080~0.140"
(2.03~3.55mm)
0.520~0.620"
(13.21~15.75mm)
0.136~0.150"
• Non-Inductive design
• Resistor package totally insulated
from heat sink
(3.45~3.81mm)
Insulation Resistance: 10GΩ min.
Dielectric Strength: 1,800 VAC
0.310~0.330"
(0.55~1.07mm)
0.054~0.066"
(1.37~1.67mm)
0.085~0.105"
(2.15~2.67mm)
0.390~0.410"
(9.90~10.42mm)
T e s T D ATA
Test
Load life
Conditions Of Test
MIL-R-39009D 4.8.13 , 2,000 hours ∆R ≤ ±(1.0% + 0.0005Ω)
at rated power
Performance
o r D e r i n G i n F o r m AT i o n
RoHS Compliant
Package Code
Non-compliant
version unavailble
Moisture
resistance
-10°C - +65°C, RH>90%, cycle 240 h ∆R ≤ ±(0.50% + 0.0005Ω)
M = two terminals
Short time
overload
1.5 times rated power and V(DC)
∆R ≤ ± (0.50% + 0.0005Ω)
≤1.5Vmax for 5 seconds
T E H 1 0 0 M 1 0 R 0 J E
Thermal shock GJB360A-96 method 107, Cond. F ∆R ≤ ±(0.50% + 0.0005Ω)
Dielectric
strength
Series
Ohms
Tolerance
F = 1%
J = 5%
GJB360A-96 method 301, (1,800V
AC, 60s)
∆R ≤ ± (0.15% + 0.0005Ω)
R = Decimal
Example:
2R50 = 2.50Ω
25R0 = 25Ω
100R = 100Ω
1K00 = 1000Ω
Terminal
strength
GJB360A-96 method 211, Cond. A
(Pull Test) 2.4N
∆R ≤ ±(0.20% + 0.0005Ω)
High frequency GJB360A-96 method 204, Cond. D ∆R ≤ ±(0.40% + 0.0005Ω)
vibration
Check product availability at www.ohmite.com
D ꢀ R A T ꢄ ꢆ G
100
s TA n D A r D p A r T n u m b e r s F o r T e H s e r i e s
80
60
40
20
0
ꢅhms
0.05
0.075
0.1
0.2
0.5
5% tolerance
1% tolerance
TEH100MR050JE
TEH100MR075JE
TEH100MR100JE
TEH100MR200JE
TEH100MR500JE
1
2
2.5
3
5
TEH100M1R00JE
TEH100M2R00JE
TEH100M2R50JE
TEH100M3R00JE
TEH100M5R00JE
TEH100M1R00FE
TEH100M2R00FE
TEH100M2R50FE
TEH100M3R00FE
TEH100M5R00FE
0
25
50
75
100
125
150
175
7.5
10
15
20
25
TEH100M7R50JE
TEH100M10R0JE
TEH100M15R0JE
TEH100M20R0JE
TEH100M25R0JE
TEH100M7R50FE
TEH100M10R0FE
TEH100M15R0FE
TEH100M20R0FE
TEH100M25R0FE
Ambient Temperature, °C
Derating (thermal resistance): 0.666W/°K (1.5K/W). Without a heatsink, when in
free air at 25°C, the TEH100 is rated for 3.5W. Derating for temp. above 25°C is
0.0234W/°K.
50
TEH100M50R0JE
TEH100M100RJE
TEH100M470RJE
TEH100M750RJE
TEH100M1K00JE
TEH100M50R0FE
TEH100M100RFE
Graphed value is only valid when using a thermal conduction to the heatsink Rth-
cs<0.025°K/W. This value can be reached by using thermal transfer compound
with a heat conductivity of 1W/mK. The flatness of the cooling plate must be better
than 0.05mm overall. The roughness of the surface should not exceed 6.4µm. The
case temperature is to be used for the definitiion of the applied power limit. The
case temperature measurement must be made with a thermocouple contacting
the center of the component mounted on the designed heat sink. Thermal grease
should be applied properly
100
470
750
1K
ꢃheck product availability
using the Worldwide ꢄnventory
ꢂearch at ohmite.com
Ohmite Mfg. Co. 1600 Golf Rd., Rolling Meadows, IL 60008 • 1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • info@ohmite.com
51