TCPP01-M12
Datasheet
USB Type-C™ and power delivery protection for sink application
Features
•
VBUS overvoltage protection, adjustable from 5 V up to 22 V, with external
N-channel MOSFET
•
•
6.0 V overvoltage protection (OVP) on CC lines against short-to-VBUS
System-level ESD protection for USB Type-C™ connector pins (CC1, CC2),
compliant with IEC 61000-4-2 level 4 (±8 kV contact discharge, ±15 kV air
discharge)
•
•
Integrated gate driver and charge pump for an external N-channel MOSFET
(featuring lower RDSON than a P-channel MOSFET) for low BOM cost
Product labels
Null quiescent current when no USB charging cable is attached for battery-
operated "consumer/sink" applications
•
•
•
Over temperature protection (OTP)
Operating junction temperature from -40°C to 125°C
Compliant with USB Type-C™ power delivery standard 3.1, standard power
range (SPR), up to 100 W
•
•
ECOPACK2 compliant
Product link and summary
USB-IF certification as power-sinking device with test ID: 5205 on X-NUCLEO-
SNK1M1 and Nucleo-STM32G071RB
Order code
TCPP01-M12
QFN-12L
Package
Packing
Applications
Tape and reel
PPS compliant USB
Type-C™ port protection
•
Any USB Type-C™ device used in UFP/sink configuration using 5 V only or
any PDO from USB power delivery, including PPS
Description
•
•
Power sinking devices: POS, gaming, healthcare, USB hub, IoT gateways
Smart speakers, earphones, smart glasses, power tools, etc.
Companion chip
Any general-purpose
Description
USB Type-C™ MCU (example: STM32
or STM8)
The TCPP01-M12 (Type-C port protection) is a single chip solution for USB Type-C™
port protection that facilitates the migration from USB legacy connectors type-A or
type-B to USB Type-C™ connectors. The TCPP01-M12 features 22 V tolerant ESD
protection as per IEC61000-4-2 level 4 on USB Type-C™ connector configuration
channel (CC) pins. For a safe and reliable USB Type-C™ implementation, the
TCPP01-M12 provides overvoltage protection on CC1 and CC2 pins when these pins
are subjected to short circuit with the VBUS pin that may happen when removing the
USB Type-C™ cable from its receptacle. For sink applications, TCPP01-M12 triggers
an external N-MOSFET on the VBUS line when a defective power source applies
a voltage higher than selected OVP threshold. Also, the TCPP01-M12 integrates a
“dead battery” management logic that is compliant with the latest USB power delivery
specification. The MCU 3.3 V GPIO provides the power supply of the TCPP01-M12
for sink applications operated with a battery in order to drop the power consumption
in “cable not attached” condition down to 0 nA. This low-power mode extends the
battery operating life when no source equipment is attached.
USB Type-C™
with power
delivery
STM32 with UCPD
support, example
STM32L5, STM32G0,
STM32G4, STM32U5
X-NUCLEO-SNK1M1
with Nucleo-
STM32G071RB or
Nucleo-STM32G474RE
Evaluation
board
NUCLEO-L552ZE-Q,
STM32L562E-DK,
STM32L552E-EV,
NUCLEO-U575ZI-Q,
STM32U575I-EV
ST
development
board with
TCPP01-M12
Introduction to USB
power delivery with
STM32
ST WIKI
The TCPP01-M12 can also be used to protect source (provider) applications, and it
can support a programmable power supply feature from the USB Type-C™ power
delivery specification.
DS12900 - Rev 7 - February 2023
For further information contact your local STMicroelectronics sales office.
www.st.com