TC9208M
Preliminary Data Sheet
8-Port 10/100/1000 Smart Ethernet Switch
This feature allows improved support for
Features
multimedia applications.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Stand Alone Switch On A Chip
The chip embeds IEEE 802.3 MAC functions for
each port and these functions support full and half
duplex modes for both 10 and 100 Mbits/s data
rates and full duplex for 1000 Mbit/s. Each port
includes dedicated receive and transmit FIFOs
with necessary logic to implement flow control for
both full and half duplex modes. TC9208M uses
IEEE 802.3x frame based flow control for full
duplex and backpressure for half duplex.
8 Ethernet 10/100/1000 ports
MII/GMII interface for all ports
Trunk group support
Four Classes of Service (CoS) selectable for
each port and/or checked via IP Header and
802.1Q VLAN Tag
ꢀ
ꢀ
Eight port-based VLANs
Maximum throughput, non head-of-line
blocking architecture
ꢀ
ꢀ
ꢀ
Embedded SSRAM packet buffer/address table
8K MAC address table
TC9208M handles an 8K address-lookup table
with searching, self-learning, and automatic aging,
at very high speed and excellent address space
coverage. Forwarding rules are implemented
according to IEEE 802.1D specifications. Filtering
capabilities for bad packets and packets with
Reserved Group Address DA are also provided.
Each port is configurable to 10 full/half duplex,
100 full/half duplex and 1000 full duplex mode
Flow-control ability is able to set for both full
and half duplex mode
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Broadcast throttling
Port Mirroring
Serial EEPROM Interface, EEPROM is optional
MDIO master for PHY configuration / polling
0.18 micron technology
Increased interconnection bandwidth can be
achieved by using TC9208M’s trunking
capabilities. Several load-balancing schemes are
provided through pin and EEPROM configuration.
A port mirror feature, which it includes bad frames
optionally, can be used for debugging network
problems.
2V and 3.3V dual voltage power supply
Packaged in PBGA 292
27 MHz crystal input only
General Description
The pin configuration interface comprises 40
configurations, which are shared with GMII output
pins by latching the configuration data during
reset. An external EEPROM device can also be
used to configure the TC9208M at power-up. With
reference to pin configuration interface, the
EEPROM extends the chip’s configuration
capability with new features and enables a
jumper-less configuration mode using a parallel
interface for reprogramming. A virtual internal
EEPROM mode is also provided to enable the
use of the programming interface in the absence
of external EEPROM. TC9208M can make
effective use by most of its features using only the
pin configuration interface.
TC9208M is a fully integrated 8 port 10/100/1000
smart Ethernet switch controller designed for low
cost and high performance solutions. The chip
embeds necessary SSRAM for packet buffering
and MAC address table. It provides MII / GMII
interface for all ports.
A store-and-forward switching method using a
non-blocking architecture is implemented within
TC9208M to improve the availability and
bandwidth. The chip embeds packet buffer, which
it supports normal and priority queues for each
transmission port.
TC9208M provides evolved CoS with four levels
of priority. The priority can be checked via layer 2
(802.1Q VLAN Tagging) and/or layer 3 (IP Header
TOS bits) packets. Port based priority is also
provided to ensure transmission with precedence
for all packets incoming from selected port(s).
TC9208M includes a physical layer configuration /
polling entity, which it is use to configure the phy
functions and to monitor the physical layer
transceiver’s speed, duplex mode, link status and
full duplex flow control ability for each port. The
chip provides four modes for phy configurations,
Confidential.
1/53
August 1, 2003
Copyright © 2003, IC Plus Corp.
TC9208M-DS-R06
5秒后页面跳转
解析光耦仿真器：升级光耦合器技术的必要性
英伟达新一代Blackwell GPU过热问题致交付延迟
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
