REVISION X
SIB-1XX-XX-XX-S-XX-XX
C
+.0040
-.0020
+0.102
0.084
-0.051
.0033
No OF POSITIONS
THREADED INSERT OPTION
DO NOT
SCALE FROM
THIS PRINT
-02 THRU -30
(SEE NOTES 9 & 10)
[NOT AVAILABLE ON 30 POS]
(PER ROW)
-E: TI-2-56-115 (ENGLISH)
*
*
*
-M: TI-M2-4-115-N (METRIC)
(SEE FIG. 2, SHEET 2)
DETAIL 'A'
SCALE 10 : 1
-TI: NO INSERTS PLACED IN BODY
(SEE TABLE 1 ON SHEET 2 FOR
-TI POSITIONAL OFFERINGS)
LEAD STYLE
-02: SURFACE MOUNT
(USE C-228-X)
OPTION
.015[.38]
.005[.13]
No OF POSITIONS x .100[2.54]
-LC: LOCKING CLIPS
(USE LC-09-TM)(SEE NOTE 13)
[N/A WITH THREADED INSERT OPTION
-E, -M OR -TI]
PLATING SPECIFICATION
-F: FLASH SELECTIVE
(USE C-228-F)
C
.050 1.27
REF
((No OF POSITIONS -1) x .100[2.54]) .005[.13]
-FM: FLASH SELECTIVE, PURE TIN,
MATTE FINISH
ROW SPECIFICATION
-S: SINGLE (USE SIBC-XX-02-S)
(USE C-228-F)
AVAILABLE TO EXISTING CUSTOMERS ONLY
*
.264 6.706 REF
.335 8.509
REF
01
.015 0.38 REF
SIBC-XX-02-S
.0287 0.729 MIN END
WALL ON CUT PART
FIG 1
SIB-120-02-X-S-LC SHOWN
C-228-X
"A"
.175 4.45 REF
'A'
C
.207±.005 5.267±0.127
.150 3.810 REF
"A"
LC-09-TM
.045 1.143
.203 5.16
(No OF POSITIONS -2) x .100[2.54] REF
(No OF POSITIONS -1) x .100(2.54) REF
.0560 1.422 REF
.044 1.13 REF
C
.071±.003 1.803±0.08
NOTES:
SECTION "A"-"A"
C
1.
REPRESENTS A CRITICAL DIMENSION.
C
2. COPLANARITY: SEE TABLE 2.
3. BURR ALLOWANCE: .0015[.038] MAX.
4. MAXIMUM CUT FLASH: .010[.3], CAN NOT EXTEND PAST TAIL.
5. MINIMUM PUSHOUT FORCE: 1 LB.
PROPRIETARY NOTE
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
6. MAXIMUM ALLOWABLE BOW: .004[.10] INCH/INCH AFTER ASSEMBLY.
7. THREADED INSERT MUST HANDLE 25 IN-OZ OF TORQUE WITHOUT
ROTATING OR LOOSENING.
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DECIMALS
ANGLES
2
8. THREADED INSERT RETENTION: 10 LBS. MINIMUM.
9. MAX VARATION FROM PIN TO PIN TO BE .002.
10. MEASURED ON UNCUT PARTS.
11. NOTE DELETED.
12. NOTE DELETED.
.XX: .01 [.3]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322
.XXX: .005 [.13]
.XXXX: .0020 [.051]
SHEET SCALE: 2:1
MATERIAL:
DO NOT SCALE DRAWING
DESCRIPTION:
X
.100 SINGLE INTERFACE BEAM ASSEMBLY
DWG. NO.
INSULATOR: LCP, COLOR: BLACK
CONTACT: PHOSPHOR BRONZE
13. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE -LC OPTION
IS NOT COMPATIBLE WITH AUTO PLACEMENT. SAMTEC RECOMMENDS
MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH THE -LC OPTION.
SIB-1XX-XX-XX-S-XX-XX
SHEET 1 OF 2
BY:
DEAN P
9/20/2000
F:\DWG\MISC\MKTG\SIB-1XX-XX-XX-S-XX-XX-MKT.SLDDRW