SFSSX-XX-XXX-XX-XX.XX-XX-XXX
REVISION E
(No OF POS x .050[1.27]) + .021[0.53] REF
E
FEP CABLE OPTION
-NXX OPTION (END 2)
(ONLY AVAILABLE WITH -D, -DR)
-NUS: NOTCH UP, STRAIGHT
(PIN 1 TO PIN 7)
-T: FEP INSULATION
LEAVE BLANK FOR STANDARD
PVC INSULATION
01
-NDS: NOTCH DOWN, STRAIGHT
(PIN 1 TO PIN 1)
No OF POSITIONS
-02 THRU -30
.200 5.08
REF
.070 1.78 REF
.095 2.41 REF
WIRE GAUGE (AWG)
END OPTION
-28
-30
(END OPTION COMBINATIONS NOT AVAILABLE)
-S: SINGLE END
.080 2.03 REF
COLOR CODE:
-D: DOUBLE END
LEAVE BLANK FOR ALL BLACK WIRE
C: COLOR CODED WIRE, SEE COLOR
SEQUENCE TABLE, SHEET 3 (SEE NOTE 10)
FIG. 1
(MUST CHOOSE FROM -NXX OPTIONS)
-SR: SINGLE ENDED WITH RETENTION LATCH
(SEE SHEET 3, FIG. 3)(USE SUB-IM-LTC-07-01-N)
(ONLY AVAILABLE ON -05 THRU -30 POS)
-DR: DOUBLE ENDED WITH RETENTION LATCH
(SEE SHEET 3, FIG. 4)(USE SUB-IM-LTC-07-01-N)
(ONLY AVAILABLE ON -05 THRU -30 POS)
(MUST CHOOSE FROM -NXX OPTIONS)
-S: SINGLE END
(SFSSX-07-28-X-XX.XX-S SHOWN)
PLATING SPECIFICATION
ISDF-XX-S
-H: HEAVY GOLD
.050 1.27 REF
"A"
-G: LIGHT GOLD
-GF: FLASH GOLD
(SEE TABLE 4, SHEET 3)
ASSEMBLED LENGTH
SPECIFY IN INCHES
(SINGLE END: 03.00 INCH [76.2mm] MINIMUM,
DOUBLE END: 03.25 INCH [82.6mm] MINIMUM)
.440 11.18
REF
.249 6.32
REF
C1
XX.XX
(SEE NOTE 8)
DWLX-08-XXX-X-XX.XX-XX-XXX
C2
XX.XX
(SEE NOTE 8)
"A"
SECTION "A"-"A"
FIG. 2
-D: DOUBLE END
(SFSSX-07-28-X-XX.XX-D-NUS SHOWN)
NOTES:
(SAME AS FIG. 1, UNLESS OTHERWISE STATED)
C
1.
REPRESENTS A CRITICAL DIMENSION.
2. MINIMUM PULLOUT FORCE: 3.0 LBS [13.3 N].
3. CONTACT MUST BE INSERTED UNTIL
RETENTION FEATURE LOCKS INTO PLACE.
PROPRIETARY NOTE
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
C3
C4
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
4. ALL FINISHED GOODS ARE TO BE ELECTICAL TESTED INCLUDING
HI-POT TEST AT 1000 VOLTS DC. AFTER FINAL ELECTICAL TEST,
LABEL EACH ASSEMBLY WITH 1 LABEL-ET.
DECIMALS
ANGLES
2
.XX: .01 [.3]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
.XXX: .005 [.13]
PHONE: 812-944-6733
FAX: 812-948-5047
code: 55322
.XXXX: .0020 [.051]
5. TINNED COPPER WIRE IS RoHS COMPLIANT.
6. PARTS TO BE LAYER PACKAGED.
e-Mail: info@SAMTEC.com
SHEET SCALE: 2:1
DO NOT SCALE DRAWING
DESCRIPTION:
MATERIAL:
7. END OF DISCRETE WIRE MUST BE IN THE RANGE AFTER CRIMP.
8. FOR LENGTHS LESS THAN 12 in, TOLERANCE SHALL BE +/-.125.
FOR OTHER LENGTHS, TOLERANCE SHALL BE +/-2%.
9. SEE DWLX-08-XX-X-XX.XX-X FOR PVC APPLICATIONS OR
DWLT-08-XX-X-XX.XX-XX-XX FOR PTFE APPLICATIONS.
10. COLOR CODED CABLE NOT AVAILABLE WITH SFSST (FEP).
.050[1.27] SOCKET DISCRETE CABLE ASSEMBLY
DWG. NO.
INSULATOR: LCP, COLOR: BLACK
CONTACT: BeCu
CABLE INSULATION: PVC
WIRE: TINNED COPPER
C4
SFSSX-XX-XXX-XX-XX.XX-XX-XXX
GAYNOR 6/12/2008
SHEET 1 OF 3
BY:
F:\DWG\MISC\MKTG\SFSSX-XX-XXX-XX-XX.XX-XX-XXX-MKT.SLDDRW