30W DC-DC Single Output
SDM30 series
Features :
Wide 2:1 DC input range
In/out capacitance1000pF
Protections: Short circuit / Overload / Over voltage
1000VDC I/O isolation for D/D
Cooling by free air convection
Built-in remote ON-OFF control
100% full load burn-in test
Fixed switching frequency at 225KHz
Lost cost
High reliability
1 year warranty
SPECIFICATION
MODEL
SDM30-12S3
SDM30-24S3
SDM30-48S3
SDM30-12S5
SDM30-24S5
SDM30-48S5
DC VOLTAGE
3.3V
5A
5V
RATED CURRENT
CURRENT RANGE
RATED POWER
5A
0 ~ 5A
16.5W
0 ~ 5A
25W
OUTPUT
RIPPLE & NOISE (max.) Note.2 75mVp-p
VOLTAGE TOLERANCE Note.3 3.0%
75mVp-p
2.0% max.
1.0%
LINE REGULATION
LOAD REGULATION
TRIM OUTPUT
1.0%
1.0%
1.0%
13%(Typ.) output voltage
10%(Typ.) output voltage
RATED DC INPUT
VOLTAGE RANGE
EFFICIENCY (Typ.)
DC CURRENT
12S: 12VDC
12S: 9.2 ~ 18VDC
77%
24S: 24VDC
24S: 18~ 36VDC
79%
24S:2A
24S/48S:30mA
48S: 48VDC
48S: 36~ 72VDC
80%
77%
79%
80%
INPUT
12S:3.6A
48S:1A
IDLE CURRENT
12S:35mA
Above 105% rated output power
Protection type : Over power limiting, recovers automatically after fault condition is removed
OVERLOAD
3.8 ~ 4.95V
5.75 ~ 7.5V
PROTECTION
OVER VOLTAGE
Protection type : Shut off o/p voltage, clamping by zener diode
SHORT CIRCUIT
ON/OFF CONTROL
WORKING TEMP.
Protection type : Constant current limiting, recovers automatically after fault condition is removed
Logic "1" or open: power on Logic "0" short to Vin-: power off
-25 ~ +85 (Refer to output load derating curve)
FUNCTION
STORAGE TEMP., HUMIDITY -25 ~ +85 , 0 ~ 95% RH
ENVIRONMENT
TEMP. COEFFICIENT
SAFETY STANDARDS
ISOLATION VOLTAGE
ISOLATION RESISTANCE
0.03%/ (0~50
Design refer to LVD
I/P-O/P:1KVDC
SAFETY &
I/P-O/P:100M Ohms/500VDC
EMC
(Note 6)
EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B
Compliance to EN61000-2,3,4,6,8; ENV50204, EN55024, light industry level, criteria A
EMS IMMUNITY
MTBF
322.4K hrs min. MIL-HDBK-217F (25
50.8*50.8*16mm (2"*2"*0.63") (L*W*H)
0.1Kg; 150pcs/15.8Kg/0.97CUFT
)
OTHERS
NOTE
DIMENSION
PACKING
1. All parameters NOT specially mentioned are measured at 12,24,48VDC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Short circuit not more than 60 second.
5. DC source wires 5cm, an input external al capacitor 47 ~ 100uF is required.
6. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
File Name:SDM30-SPEC 2007-05-24