5秒后页面跳转
SA615D/01,118 PDF预览

SA615D/01,118

更新时间: 2024-01-07 05:48:46
品牌 Logo 应用领域
恩智浦 - NXP 光电二极管商用集成电路
页数 文件大小 规格书
14页 125K
描述
SA615 - High performance low power mixer FM IF system SOP 20-Pin

SA615D/01,118 技术参数

生命周期:Active零件包装代码:SOP
包装说明:SOP,针数:20
Reach Compliance Code:compliantHTS代码:8542.39.00.01
风险等级:0.42其他特性:IN-BUILT QUADRATURE DETECTOR
商用集成电路类型:AUDIO SINGLE CHIP RECEIVER解调类型:FM
JESD-30 代码:R-PDSO-G20JESD-609代码:e4
长度:12.8 mm湿度敏感等级:1
功能数量:1端子数量:20
最高工作温度:85 °C最低工作温度:-40 °C
标称输出电压(调频):150 mV封装主体材料:PLASTIC/EPOXY
封装代码:SOP封装形状:RECTANGULAR
封装形式:SMALL OUTLINE峰值回流温度(摄氏度):260
认证状态:Not Qualified座面最大高度:2.65 mm
信噪比Nom(FM):68 dB最大供电电压 (Vsup):8 V
最小供电电压 (Vsup):4.5 V表面贴装:YES
温度等级:INDUSTRIAL端子面层:Nickel/Palladium/Gold (Ni/Pd/Au)
端子形式:GULL WING端子节距:1.27 mm
端子位置:DUAL处于峰值回流温度下的最长时间:30
宽度:7.5 mmBase Number Matches:1

SA615D/01,118 数据手册

 浏览型号SA615D/01,118的Datasheet PDF文件第5页浏览型号SA615D/01,118的Datasheet PDF文件第6页浏览型号SA615D/01,118的Datasheet PDF文件第7页浏览型号SA615D/01,118的Datasheet PDF文件第9页浏览型号SA615D/01,118的Datasheet PDF文件第10页浏览型号SA615D/01,118的Datasheet PDF文件第11页 
Philips Semiconductors  
Product specification  
High performance low power mixer FM IF system  
SA615  
RF GENERATOR  
SA615 DEM0–BOARD  
45MHz  
RSSI  
AUDIO  
DATA  
V
CC  
(+6)  
C–MESSAGE  
DC VOLTMETER  
HP339A DISTORTION  
ANALYZER  
SCOPE  
SR00345  
Figure 5. SA615 Application Circuit Test Set Up  
NOTES:  
1. C-message: The C-message filter has a peak gain of 100 for accurate measurements. Without the gain, the measurements may be  
affected by the noise of the scope and HP339 analyzer.  
2. Ceramic filters: The ceramic filters can be 30kHz SFG455A3s made by Murata which have 30kHz IF bandwidth (they come in blue), or  
16kHz CFU455Ds, also made by Murata (they come in black). All of our specifications and testing are done with the more wideband filter.  
3. RF generator: Set your RF generator at 45.000MHz, use a 1kHz modulation frequency and a 6kHz deviation if you use 16kHz filters, or  
8kHz if you use 30kHz filters.  
4. Sensitivity: The measured typical sensitivity for 12dB SINAD should be 0.22µV or –120dBm at the RF input.  
5. Layout: The layout is very critical in the performance of the receiver. We highly recommend our demo board layout.  
6. RSSI: The smallest RSSI voltage (i.e., when no RF input is present and the input is terminated) is a measure of the quality of the layout and  
design. If the lowest RSSI voltage is 250mV or higher, it means the receiver is in regenerative mode. In that case, the receiver sensitivity  
will be worse than expected.  
7. Supply bypass and shielding: All of the inductors, the quad tank, and their shield must be grounded. A 10–15µF or higher value tantalum  
capacitor on the supply line is essential. A low frequency ESR screening test on this capacitor will ensure consistent good sensitivity in  
production. A 0.1µF bypass capacitor on the supply pin, and grounded near the 44.545MHz oscillator improves sensitivity by 2–3dB.  
8. R5 can be used to bias the oscillator transistor at a higher current for operation above 45MHz. Recommended value is 22k, but should not  
be below 10k.  
8
1997 Nov 07  

与SA615D/01,118相关器件

型号 品牌 描述 获取价格 数据表
SA615DK NXP High performance low power mixer FM IF system

获取价格

SA615DK,112 NXP SA615 - High performance low power mixer FM IF system SSOP2 20-Pin

获取价格

SA615DK,118 NXP SA615 - High performance low power mixer FM IF system SSOP2 20-Pin

获取价格

SA615DK/01,112 NXP SA615 - High performance low power mixer FM IF system SSOP2 20-Pin

获取价格

SA615DK-T NXP 暂无描述

获取价格

SA615D-T NXP 暂无描述

获取价格