Available as: QBH-1423PM, 4 Pin TO-8 (T4)
QBH-5023PM, 4 Pin Surface Mount (SM3)
RF AMPLIFIER
QBH-9-1423PM, Connectorized Housing (H1)
MODEL
QBH-1423PM
Features
Typical Intermodulation Performance at 25ºC
Second Order Harmonic Intercept Point ....... +46 dBm (Typ.)
Second OrderTwoTone Intercept Point ........ +40 dBm (Typ.)
Third OrderTwoTone Intercept Point ............ +34 dBm (Typ.)
ꢀ Superior Phase Noise Performance
ꢀ Replaces Avantek’s “1023” Design
ꢀ Operating Temp. -55 ºC to +85 ºC
ꢀ Environmental ScreeningAvailable
Absolute Maximum Ratings
Specifications
CHARACTERISTIC
Ambient OperatingTemperature ................-55ºC to +100 ºC
StorageTemperature .................................-62ºC to +125 ºC
DCVoltage .......................................................... +17 Volts
Continuous RF Input Power1 .......................................................... +17 dBm
Short Term RF Input Power1 ..... 100 Milliwatts (1 Minute Max.)
TYPICAL
Ta= 25 ºC
10 - 1000 MHz
MIN/MAX
Ta = -55 ºC to +85 ºC
10 - 1000 MHz
Frequency
Gain (dB)
13.0
12.0 Min.
±
±
Gain Flatness (dB)
0.25
0.75 Max.
MTBF Calculation for Ground Benign Environment
@ 25ºC .................................................1,674,483.59 hrs
25ºC Phase Noise Performance in dBc/Hz @ 600 MHz2
Power @ 1 dB Comp.
(dBm)
(10-500 MHz)
28.0
26.5
25.5 Min.
25.0 Min.
(500-1000 MHz)
Frequency offset
10 Hz
Typical
-150
Guaranteed
-145
Reverse
Isolation (dB)
-17
-15 Max.
VSWR
In
Out
1.5:1
1.5:1
6.0
2.0:1 Max.
2.0:1 Max.
9.0 Max.
-160
-155
100 Hz
1 kHz
-170
-175
-175
-175
-175
-180
-180
-180
Noise Figure (dB)
10 kHz
100 kHz
1 MHz
Power
Vdc
mA
+15
195
+15
210 Max.
1
Notes: Care should always be taken to effectively ground the case of each unit.
Measured in a 50 Ohm system @ +15 Volts DC nominal unless otherwise noted.
RF output terminated into 50 Ohms.
2
Phase noise performance may vary within the frequency band.
Typical Performance Data
Phase Noise (dBc/Hz)
Reverse Isolation (dB)
Gain (dB)
0
-10
-20
-30
-40
15
-130
14
13
-140
-150
12
11
-160
Start 10 MHz
Stop 100 0 MHz
Start 1 0 MHz
Stop 100 0 MHz
-170
-180
-190
1 dB Comp. (dBm)
Noise Figure (dB)
+29
+28
+27
+26
+25
8
7
6
10 k
10 0k
10
100
1k
1 M
5
4
Typical
Start 10 MHz
Stop 10 00 MHz
Start 10 MHz
Stop 100 0 MHz
Input VSWR
Residual Phase Noise Test Conditions:
Carrier Frequency: 600 MHz
Power Output: +27.0 dBm
Temperature: 25 ºC
Output VSWR
2.0
1.5
1.0
*
2.0
1.5
ꢀ
ꢀ
ꢀ
ꢀ
Agilent ES5500 System
1.0
Start 10 MHz
Sto p 1 000 MHz
Start 10 MHz
Stop 1000 MHz
Legend
+25 ºC
+85 ºC - - - - - - -55 ºC
Linear S-Parameters Data
– – S11– –
FREQ.
MHz
– – S21– –
Mag Ang
– – S12– –
Mag
– – S22– –
Mag Ang
Mag Ang
Ang
==================================================================
0.11
0.11
0.12
0.13
0.14
0.15
0.15
151.8
148.5
124.8
97.0
10
250
0.11
0.02
0.01
0.02
0.05
0.12
0.16
4.70
4.66
4.55
4.49
4.51
4.58
4.60
8.8
-34.4
0.23
0.14
0.14
0.15
0.13
0.13
0.14
-61.9
-83.6
-171.7
126.7
15.7
-44.2
-70.8
-172.3
116.7
54.5
500
-70.5
750
-109.3
-151.2
173.5
155.1
-7.5
40.7
1000
1200
1300
-70.8
-123.8
-151.8
-25.7
-68.5
Rev.
9/24/09
Spectrum Microwave · 2144 Franklin Drive N.E. · Palm Bay, Florida 32905 · PH (888) 553-7531 · Fax (888) 553-7532
Spectrum Microwave · 2707 Black Lake Place · Philadelphia, Pennsylvania 19154 · PH (215) 464-4000 · Fax (215) 464-4001
www.SpectrumMicrowave.com