Tentative
Conductive Polymer
No.722C / Jan.2003
Engineering Bulletin
Aluminum Solid Capacitors
Feature
!
@Super low ESR, impedance and high heat resistance have been obtained by using
conductive polymer as electrolyte.
(ESR and rated ripple current values are improved from PXA series.)
@Rated voltage range : 2.5 to 16Vdc, Capacitance range : 27 to 470MF
@Case size range : F5B6.0mm to F8B7.0mm
Pb Free Type
@Suitable for DC-DC converters, voltage regulators and decoupling applications used to
computer motherboards etc.
?SPECIFICATIONS
Items
Characteristics
Category
Temperature Range
-
55 to +105C
Rated Voltage Range 2.5 to 16Vdc
Capacitance Tolerance P20% (M)
(at 20C, 120Hz)
(at 105C)
Surge Voltage
Rated voltageB1.15V
I=0.2CV (max.)
Leakage Current
I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (Vdc
)
(at 20C after 2 minutes)
(at 20C, 120Hz)
Dissipation Factor
(tane)
0.12 max.
Low Temperature
Characteristics
Z(
-
25C)/Z(+20C)[1.15
(Max. Impedance Ratio) Z(
-55C)/Z(+20C)[1.25
(at 100kHz)
Endurance
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 1000 hours
at 105C.
Appearance
Capacitance change
DF (tanE)
No significant damage
[P20% of the initial value
[150% of the initial specified value
[150% of the initial specified value
[The initial specified value
ESR
Leakage current
Bias Humidity
Surge Voltage
Failure Rate
The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to the DC rated voltage at
60C, 90 to 95% RH for 500 hours.
Appearance
Capacitance change
DF (tanE)
No significant damage
[P20% of the initial value
[150% of the initial specified value
[150% of the initial specified value
[The initial specified value
ESR
Leakage current
The capacitors shall be subjected to 1000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds
through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds.
Appearance
Capacitance change
DF (tanE)
No significant damage
[P20% of the initial value
[150% of the initial specified value
[150% of the initial specified value
[The initial specified value
ESR
Leakage current
1% per 1000 hours maximum (Confidence level 60% at 105C)
*Note : If any doubt arises, measure the leakage current after following voltage treatment.
Voltage treatment : DC rated voltage are applied to the capacitors for 120 minutes at 105C.
?DIMENSIONS [mm]
?MARKING
EX) PXC4VC220M
W
C28M
220
4V
Case code fD
L
A
B
C
W
P
E60
F60
H70
5
5.7 5.3 5.3 5.9 0.5 to 0.8 1.4
6.3 5.7 6.6 6.6 7.2 0.5 to 0.8 1.9
6.7 8.3 8.3 9.0 0.7 to 1.1 3.1
8
0.3max.
LP0.3
AP0.2
?PART NUMBERING SYSTEM
PXC
4
VC 220
M
F60
Case code
Capacitance
39MF
Code
39
100
220
Cap tolerance (P20%)
Nominal cap code
Terminal type
Rated voltage in volts
Series name
100MF
220MF
Specifications in this bulletin are subject to change without notice.
Please ask us for technical specifications before purchase and use.
NIPPON CHEMI-CON CORPORATION
1
1149