5秒后页面跳转
PM912NE812AMAF PDF预览

PM912NE812AMAF

更新时间: 2024-01-20 12:32:35
品牌 Logo 应用领域
飞思卡尔 - FREESCALE /
页数 文件大小 规格书
19页 476K
描述
S12P MCU and Multifunctional Ignition

PM912NE812AMAF 数据手册

 浏览型号PM912NE812AMAF的Datasheet PDF文件第2页浏览型号PM912NE812AMAF的Datasheet PDF文件第3页浏览型号PM912NE812AMAF的Datasheet PDF文件第4页浏览型号PM912NE812AMAF的Datasheet PDF文件第5页浏览型号PM912NE812AMAF的Datasheet PDF文件第6页浏览型号PM912NE812AMAF的Datasheet PDF文件第7页 
Document Number: MM912_P812  
Rev. 1.0, 05/2012  
Freescale Semiconductor  
Advance Information  
S12P MCU and Multifunctional  
Ignition and Injector Driver  
System In Package (SiP)  
912_P812  
The MM912xP812 is an engine control IC combining an MCU  
(S12P) and analog control die (MC33812) intended for motorcycle  
and other single/dual cylinders small engine control applications.  
SMALL ENGINE CONTROL SIP  
The MCU S12P has 6 KB RAM, and flash memory size of 96 KB  
or 128 KB. The S12P family uses many of the same features found  
on the S12XS family, including error correction code (ECC) on flash  
memory, a separate data-flash module for diagnostic or data  
storage, a fast analog-to-digital converter (ATD), and a frequency  
modulated phase locked loop (IPLL) that improves the  
electromagnetic compatibility (EMC) performance.  
The analog control IC consists of three integrated low side drivers,  
one pre-driver, a +5.0 V, voltage pre-regulator, an MCU watchdog  
circuit, an ISO 9141 K-Line interface, and a parallel interface for  
MCU communication. The three low side drivers are provided for  
driving a fuel injector, a lamp or LED, and a relay or another injector  
or fuel pump. The pre-driver is intended to drive either an insulated  
gate bipolar transistor (IGBT) or a bipolar Darlington transistor to  
control an ignition coil.  
98ASA00371D  
100 Pin LQFP-EP  
Features:  
• Designed to operate over the range of ~4.7 V VPWR 36 V  
• Relay/injector/fuel pump driver—current limit—4.0 A typical  
• Lamp driver—current limit—1.5 A typical  
• All external outputs protected against short to battery and over-current  
• VCC voltage pre-regulator provides +5.0 V power for the MCU  
• MCU watchdog timer circuit with parallel refresh/time setting line  
• ISO-9141 K-Line transceiver for communicating diagnostic messages  
• All signal lines are accessible  
• Also available with MC9S12XEP100 MCU for calibration  
• For detailed specifications see data sheets for the MC33812 and MC9S12Pxxx  
• Provides single package ECU for minimum PC board area  
V
BAT  
V
BAT  
V
V
BAT  
BAT  
912_P812  
Relay or  
other load  
5.0 V  
VDD  
VCCSENS  
LAMPOUT  
ROUT  
Injector  
INJOUT  
IGNFB  
VCCREF  
V
IGNSUP  
IGNOUTH  
IGNOUTL  
ISO9141  
PAD0  
PAD1  
PAD2  
PAD3  
PAD4  
PAD5  
PAD6  
PAD7  
PAD9  
MOSI  
SCK  
SS  
V
PWR  
BAT  
VPWR  
LAMPIN  
I/O  
RIN  
I/O  
ISO9141  
RESET  
RESET  
WDRFSH  
I/O  
INJIN  
I/O  
INJFLT  
I/O  
IGNIN  
I/O  
IGNFLT  
I/O  
RELFLT  
I/O  
MRX  
RXD  
MTX  
TXD  
Notes  
1. Surge Voltage protection  
recommended on VPWR  
2. Not all connections on MCU shown  
MISO  
IRQ  
PM1/TXCAN  
PM0/RXCAN  
TEST1  
TM_EN, TEST2  
WD_INH  
PGND  
DGND  
EXTAL  
XTAL  
VSS  
Figure 1. MM912_P812 Simplified Application Diagram  
*This document contains certain information on a product under development.  
Freescale reserves the right to change or discontinue this product without notice  
© Freescale Semiconductor, Inc., 2012. All rights reserved.  

与PM912NE812AMAF相关器件

型号 品牌 获取价格 描述 数据表
PM913 ARTESYN

获取价格

Single and dual output 5 to 6 Watt Nominal input DC/DC converters
PM914 ETC

获取价格

Analog IC
PM914B ETC

获取价格

Analog IC
PM921 ARTESYN

获取价格

Single and dual output 5 to 6 Watt Nominal input DC/DC converters
PM-9210 PMI

获取价格

Datacom Transformer,
PM921A ETC

获取价格

Analog IC
PM921B ETC

获取价格

Analog IC
PM923 ARTESYN

获取价格

Single and dual output 5 to 6 Watt Nominal input DC/DC converters
PM924 ARTESYN

获取价格

Single and dual output 5 to 6 Watt Nominal input DC/DC converters
PM931 ETC

获取价格

Analog IC