PIC18F6410/8410
64/80-Pin High-Performance, Flash Microcontrollers with
10-bit A/D and nanoWatt Technology Product Brief
Low-Power Features:
Peripheral Highlights:
• Power Managed modes:
• High current sink/source 25 mA/25 mA
- Run: CPU on, peripherals on
- Idle: CPU off, peripherals on
- Sleep: CPU off, peripherals off
• Power Consumption modes:
- PRI_RUN: 150 µA @ 1 MHz, 2V
- PRI_IDLE: 35 µA @ 1 MHz, 2V
- SEC_RUN: 9.6 µA @ 32 kHz, 2V
- SEC_IDLE: 5.8 µA @ 32 kHz, 2V
- RC_RUN: 145 µA @ 1 MHz, 2V
- RC_IDLE: 85 µA @ 1 MHz, 2V
- Sleep: 0.1 µA
• Up to four external interrupts
• Four 8-bit/16-bit Timer/Counter modules
• Three Capture/Compare/PWM (CCP) modules:
- Capture is 16-bit, max. resolution 6.25 ns (TCY/16)
- Compare is 16-bit, max. resolution 100 ns (TCY)
- PWM output: PWM resolution is up to 10-bit
• Master Synchronous Serial Port (MSSP) module
with two modes of operation:
- 3-wire SPI™ (supports all 4 SPI modes)
- I2C™ Master and Slave mode
• One Addressable USART module
• One Enhanced Addressable USART module:
- Supports LIN 1.2
• Timer1 Oscillator: 1.8 µA typical @ 32 kHz, 2V
• Watchdog Timer: 2.2 µA @ 2V
• Two-Speed Oscillator Start-up
- Auto-wake-up on Start bit
- Auto-baud detect
• 10-bit, up to 12-channel A/D Converter:
- Auto-acquisition
- Conversion available during Sleep
• Two analog comparators
Flexible Oscillator Structure:
• Four Crystal modes:
- LP: up to 200 kHz
- XT: up to 4 MHz
- HS: up to 40 MHz
• Programmable reference voltage for comparators
- HSPLL: 4-10 MHz (16-40 MHz internal)
• Two External Clock modes, up to 40 MHz
• Two External RC modes, up to 4 MHz
• Internal Oscillator block:
Special Microcontroller Features:
• 1000 erase/write cycle Flash program memory typical
• Flash retention 100 years typical
- 8 user selectable frequencies: 31.25 kHz,
125 kHz, 250 kHz, 500 kHz, 1 MHz, 2 MHz,
4 MHz or 8 MHz
- 4x PLL option generates 16 MHz or 32 MHz
- Two modes select one or two I/O pins
- OSCTUNE – Allows user to shift frequency
• Secondary Oscillator using Timer1 @ 32 kHz
• Fail-Safe Clock Monitor:
• Priority levels for interrupts
• 8 x 8 Single Cycle Hardware Multiplier
• Power-on Reset (POR), Power-up Timer (PWRT)
and Oscillator Start-up Timer (OST)
• Programmable Brown-out Reset (BOR)
• Programmable 16-level Low-Voltage Detection
(LVD) module
• Extended Watchdog Timer (WDT):
- Programmable period from 4 ms to 131s
• In-Circuit Serial Programming™ (ICSP™) via two pins
• In-Circuit Debug via two pins
- Allows for safe shutdown of device if primary or
secondary oscillator/clock fails
External Memory Interface
(PIC18F8410 Devices only):
• Wide operating voltage range: 2.0V to 5.5V
• Address capability of up to 2 Mbytes
• 16-bit/8-bit interface
Program Memory
(On-board/External)
Data
Device
Memory
(bytes)
I/O
# Single Word
Instructions
Bytes
16K/0
PIC18F6410
8192/0
768
768
54
70
12
12
2
2
3
3
Y
Y
1/1
1/1
1/3
1/3
PIC18F8410 16K/2M
8192/1M
2003 Microchip Technology Inc.
Advance Information
DS39619A-page 1