MX29F800T/B
8M-BIT [1Mx8/512Kx16] CMOS FLASH MEMORY
FEATURES
• 1,048,576 x 8/524,288 x 16 switchable
• Single power supply operation
eraseoperationcompletion.
• Ready/Busy pin (RY/BY)
- 5.0V only operation for read, erase and program
operation
- Provides a hardware method of detecting program
oreraseoperationcompletion.
• Fast access time: 70/90/120ns
• Sectorprotection
• Low power consumption
- Sector protect/chip unprotect for 5V/12V system.
- Hardware method to disable any combination of
sectors from program or erase operations
-Temporarysectorunprotectallowscodechangesin
previously locked sectors.
- 50mA maximum active current
- 0.2uA typical standby current
• Command register architecture
- Byte/word Programming (7us/12us typical)
- Sector Erase (Sector structure 16K-Bytex1,
8K-Bytex2, 32K-Bytex1, and 64K-Byte x15)
• Auto Erase (chip & sector) and Auto Program
-Automaticallyeraseanycombinationofsectorswith
Erase Suspend capability.
• 100,000minimumerase/programcycles
• Latch-up protected to 100mA from -1V to VCC+1V
• Boot Code Sector Architecture
- T = Top Boot Sector
- B = Bottom Boot Sector
- Automatically program and verify data at specified
address
• Low VCC write inhibit is equal to or less than 3.2V
• Package type:
• Erase suspend/Erase Resume
- 44-pin SOP
- Suspends sector erase operation to read data from,
or program data to, another sector that is not being
erased, then resumes the erase.
- 48-pin TSOP
• Compatibility with JEDEC standard
- Pinout and software compatible with single-power
supply Flash
• Status Reply
-Datapolling&Togglebitfordetectionofprogramand
GENERAL DESCRIPTION
The MX29F800T/B is a 8-mega bit Flash memory or-
ganized as 1M bytes of 8 bits or 512K words of 16 bits.
MXIC's Flash memories offer the most cost-effective and
reliable read/write non-volatile random access memory.
The MX29F800T/B is packaged in 44-pin SOP, 48-pin
TSOP. It is designed to be reprogrammed and erased
in system or in standard EPROM programmers.
TTL level control inputs and fixed power supply levels
during erase and programming, while maintaining maxi-
mum EPROM compatibility.
MXIC Flash technology reliably stores memory contents
even after 100,000 erase and program cycles. The MXIC
cell is designed to optimize the erase and programming
mechanisms. In addition, the combination of advanced
tunnel oxide processing and low internal electric fields
for erase and program operations produces reliable cy-
cling. The MX29F800T/B uses a 5.0V±10% VCC sup-
ply to perform the High Reliability Erase and auto Pro-
gram/Erase algorithms.
The standard MX29F800T/B offers access time as fast
as 70ns, allowing operation of high-speed microproces-
sors without wait states. To eliminate bus contention,
the MX29F800T/B has separate chip enable (CE) and
output enable (OE) controls.
MXIC's Flash memories augment EPROM functionality
with in-circuit electrical erasure and programming. The
MX29F800T/B uses a command register to manage this
functionality. The command register allows for 100%
The highest degree of latch-up protection is achieved
with MXIC's proprietary non-epi process. Latch-up pro-
tection is proved for stresses up to 100 milliamps on
address and data pin from -1V to VCC + 1V.
P/N:PM0578
REV. 2.5, NOV. 05, 2004
1