Advance‡
MT9D012: 1/4-Inch 2-Megapixel Image Sensor Die
Features
1/4-Inch 2-Mp CMOS Digital Image Sensor Die
MT9D012 Die Data Sheet
For the product data sheet, refer to Aptina’s Web site: www.aptina.com
Die Database
• Die outline, see Figure 3 on page 9
• Singulated die size:
Features
®
®
• Aptina DigitalClarity CMOS imaging technology
• Low dark current
• Simple two-wire serial interface
• Auto black level calibration
6,003µm ±25µm x 5,404µm ±25µm
• Bond Pad Location and Identification Tables, see
pages 5–8
• Support for external mechanical shutter
• Support for external LED or xenon flash
• High frame rate preview mode with arbitrary
downsize scaling from maximum resolution
• Programmable controls: Gain, frame size/ rate,
exposure, left-right and top-bottom image reversal,
window size and panning
Options
• Form
– Die
D
• Testing
– Standard (level 1) probe
C1
• SMIAcom patible
Notes: 1. Consult die distributor or factory before ordering to
verify long-term availability of these die products.
• Data interfaces: Parallel and CCP2 compliant
sub-low-voltage differential signaling (sub-LVDS)
• On-die phase-lock loop (PLL) oscillator
• Bayer-pattern down-size scaler
Key Performance Parameters
• Optical format: 1/ 4-inch UXGA (4:3)
• Active imager size: 3.56mm(H) x 2.68mm(V),
4.45mm diagonal
• Integrated color/ lens shading correction
• Superior low-light performance
• Active pixels: 1616H x 1216V
• Pixel size: 2.2µm x 2.2µm
• Color filter array: RGB Bayer Pattern
• Shutter type: Electronic rolling shutter (ERS)
• Maxim um data rate/ master clock:
64 Mp/ s at 64 MHz PIXCLK
General Physical Specifications
• Die thickness: 200µm ±12µm
(Consult factory for die thickness other than 200µm)
• Backside die surface of bare silicon
• Typical metal 1 thickness: 3.1kÅ
• Typical metal 2 thickness: 3.1kÅ
• Typical metal 3 thickness: 6.1kÅ
• Metallization composition: 99.5 percent Al and 0.5
percent Cu over Ti
• Frame rate:
UXGA (1600H x 1200V) programmable up to 22 fps
VGA (640H x 480V) programmable up to 60 fps
• ADC resolution: 10-bit, on-die (61dB)
• Responsivity: 0.53 V/ lux-sec
• Typical topside passivation:
2.2kÅ nitride over 6.0kÅ of undoped oxide
• Passivation openings (MIN): 75µm x 90µm
• Dynamic range: 59.5dB
• SNR
: 37.7dB
MAX
• Supply voltage
Order Information
MT9D012D00STCC15AC1
Analog: 2.4–3.1V (2.5V or 2.8V nominal)
Digital: 1.7–1.9V (1.8V nominal)
I/ O: 1.7–3.1V
Die
Database
Testing
Level
• Power consumption: TBD
• Operating temperature: –30°C to +70°C
Product#
Form
Temp
Chrom
PDF: 8729523836/Source: 2562915520
MT9D012_DDS - Rev. F; Pub. 5/10 EN
Aptina reserves the right to change products or specifications without notice.
©2006 Aptina Imaging Corporation All rights reserved.
1
‡Products and specifications discussed herein are for evaluation and reference purposes only and are subject to change by Aptina without
notice. Products are only warranted by Aptina to meet Aptina’s production data sheet specifications. Specifications discussed herein are
subject to change without notice. This product is sold “as is” and is delivered with no guarantees or warranties, express or implied.