MP9100 TO-247 Kool-Pak® Power Film Resistor
TO-247 Style Power Package 100 Watt Non-Inductive Design
•
•
•
•
•
•
•
100 watt continuous power at +25°C case temperature
TO-247 package utilizes proven power semiconductor thermal solutions
Equivalent to UL94 V-O flammability rating
Excellent pulse/surge performance
Non-inductive design for high speed switching, snubbers and rf applications
Safe and reliable operation up to +175°C case temperature
Electrically isolated case
Maximum Ratings
Rating
Power Dissipation: With heat sink T =25°C
Symbol
Value
100
Unit
Watts
Watts
P
D
C
P
D
3.5
Free Air at 25°C without heat sink
R
˚C/W
˚C
Thermal Resistance: Resistance film (J) to Case (C)
Operating and Storage Temperature Range
1.5
θJC
T
,T , T
-55 to +175
These products are covered by one or more
patents, also patents pending.
C
J
STG
(1)
Derating Using Case Temperature (T ):
C
Single Pulse/Surge Ratings:
Electrical Specifications:
Temperature Coefficient:
TC referenced to +25°C, ∆R taken at +175°C
0.50 ohm and above, -20 to +80 ppm/°C
0.050 ohm to 0.49 ohm, 0 to +150 ppm/°C
T
= 25°C with no continuous power
All power and overload ratings are derated based
upon case temperature using the derating curve.
The case temperature is measured at the center of
the ceramic mounting surface, with the part properly
mounted and under electrical load
C
applied, derate per Fig. 1
Duration
10 µsec
Energy
Units
Joules
Joules
Joules
Joules
Joules
Joules
volts peak
0.07
0.25
0.9
3.5
15
Derating Curve
(Fig. 1)
100 µsec
1 msec
Inductance: 10 nH typical in series when mea-
sured at the shoulder of the lead
100
80
Capacitance: <1 pf typical without heat sink
10 msec
100 msec
250 msec
V maximum
60
DWV: 1500 V AC isolation to the mounting
RATED POWER OR
surface or a clRipMSin contact with the top surface
PULSE ENERGY, %
40
38
Insulation Resistance: 10,000 Megohms, min.
The resistor element is electrically isolated from
the mounting surface.
600
20
0
(1) For multiple pulses/surge ratings please
contact applications engineering for assistance
25
100
175
CASE TEMPERATURE, oC
Momentary Overload: 1.5 times rated power for
5 seconds, ∆R ±(0.5 percent + 0.0005 ohm) max.,
based on a case temperature of +175°C max.
Mounting Note: Mount on a smooth, clean and flat heat sink surface with a thermal interface material,
such as thermal grease. The entire exposed ceramic portion must be in contact with the heat sink.
When screw mounting, use a Belleville washer which provides a mounting force of 150 to 300 pounds
(665 to 1330 N). Mounting torque to avoid package damage is 8 in-lbs. (0.90 N-m). If a spring clip is
used, a clip force of 4.5 to 35 pounds (20 to 155 N) is recommended
Environmental Specifications:
Load Stability: 2000 hours at rated power
∆R less than ±(1% +0.0005Ω)
Standard Resistance Values:
Moisture Resistance: Mil-Std-202, Method 106,
∆R ±(0.5 percent + 0.0005 ohm) max.
Tolerance: 1% Standard
0.620 ± 0.010
(15.75 ± 0.26)
0.195 ± 0.010
(4.95 ± 0.26)
0.143 ± 0.004
(3.63 ± 0.10) Dia.
C
L
0.050 Ω
0.10 Ω
0.12 Ω
0.15 Ω
0.20 Ω
0.25 Ω
0.30 Ω
0.33 Ω
0.39 Ω
0.50 Ω
0.75 Ω
1.00 Ω
1.50 Ω
2.00 Ω
2.20 Ω
2.50 Ω
3.00 Ω
3.30 Ω
3.90 Ω
5.00 Ω
8.00 Ω
10.0 Ω
12.0 Ω
15.0 Ω
18.0 Ω
20.0 Ω
22.0 Ω
25.0 Ω
27.0 Ω
33.0 Ω
39.0 Ω
47.0 Ω
50.0 Ω
56.0 Ω
75.0 Ω
100 Ω
Thermal Shock: Mil-Std-202, Method 107, Cond.
F, ∆R ±(0.5 percent + 0.00005 ohm) max.
0.210 ± 0.010
(5.33 ± 0.26)
Shock: 100G, Mil-Std-202, Method 213,
Cond. I, ∆R ±(0.4 percent + 0.0005 ohm) max.
0.815 ± 0.010
(20.70 ± 0.26)
Vibration, High Frequency: Mil-Std 202, Method
204, Condition D, ∆R±(0.4% +0.0005Ω) max.
MP9100
50.0
1%
0.110 ± 0.030
(2.79 ± 0.76)
Terminal Strength: Mil-Std-202, Method 211,
Cond. A (Pull Test) 5 lbs.,
∆R ±(0.2 percent + 0.0005 ohm) max.
0.143 ± 0.015
(3.63 ± 0.38)
0.570 ± 0.050
(14.48 ± 1.27)
For custom values and tolerances contact
applications engineering
0.060 ± 0.004
(1.52 ± 0.10)
Measurement Note: Resistance measurements
shall be made at 0.2 inch (5.08 mm) from the
resistor body
0.032 +0.004 / -0.010
(0.81 +0.10 / -0.026)
Ordering Information:
Parts shipped 25 per anti static plastic tube
0.400 ± 0.010
(10.16 ± 0.26)
0.095 ± 0.010
(2.41 ± 0.26)
For more information please see our website:
Application Note: CAD-9100-1
MP9100 - 0.050 - 1%
Tolerance
Model Number:
(1% Std)
DIMENSIONS IN INCHES AND (MILLIMETERS)
Resistor Value:
(see table)
RHOPOINT COMPONENTS LTD.
Holland Road
Hurst Green
Tel: +44 (0)1883 717988
Fax: +44 (0)1883 712938
Email: components@rhopoint.co.uk
Website: www.rhopoint.co.uk/components/
CADDOCK
Oxted, Surrey, RH8 9AX
www.caddock.com
IL-127.010
©
2000 Caddock Electronics, Inc.
5秒后页面跳转
解析光耦仿真器：升级光耦合器技术的必要性
英伟达新一代Blackwell GPU过热问题致交付延迟
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
