Order this document
by MOC2R60–10/D
SEMICONDUCTOR TECHNICAL DATA
*Motorola Preferred Devices
This device consists of a gallium arsenide infrared emitting diode optically coupled
to a random phase triac driver circuit and a power triac. It is capable of driving a load
of up to 2 amps (rms) directly, on line voltages from 20 to 280 volts AC (rms).
•
•
•
•
•
•
Provides Normally Open Solid State AC Output with 2 Amp Rating
70 Amp Single Cycle Surge Capability
OPTOISOLATOR
2 AMPS
RANDOM–PHASE
TRIAC OUTPUT
600 VOLTS
Phase Controllable
High Input-Output Isolation of 3750 vac (rms)
Static dv/dt Rating of 400 Volts/µs Guaranteed
2 Amp Pilot Duty Rating Per UL508 117 (Overload Test)
and 118 (Endurance Test)
[File No. 129224]
•
•
CSA Approved [File No. CA77170-1]. VDE Approval in Process.
Exceeds NEMA 2-230 and IEEE472 Noise Immunity Test Requirements
(See Figure 17)
CASE 417-02
Style 2
PLASTIC PACKAGE
DEVICE RATINGS (T = 25°C unless otherwise noted)
A
9
7
Rating
INPUT LED
Symbol
Value
Unit
3
2
Forward Current — Maximum Continuous
I
50
mA
A
F
Forward Current — Maximum Peak
(PW = 100µs, 120 pps)
I (pk)
F
1.0
CASE 417A-02
Style 1
PLASTIC PACKAGE
Reverse Voltage — Maximum
OUTPUT TRIAC
V
R
6.0
V
Output Terminal Voltage — Maximum Transient (1)
V
DRM
600
V(pk)
Operating Voltage Range — Maximum Continuous
(f = 47–63 Hz)
V
T
20 to 280
Vac(rms)
CASE 417B-01
Style 1
PLASTIC PACKAGE
On-State Current Range
(Free Air, Power Factor ≥ 0.3)
I (rms)
0.03 to 2.0
70
A
A
T
Non-Repetitive Single Cycle Surge Current —
Maximum Peak (t = 16.7 ms)
I
TSM
DEVICE SCHEMATIC
2
2
Main Terminal Fusing Current (t = 8.3 ms)
Load Power Factor Range
Junction Temperature Range
TOTAL DEVICE
I T
26
A sec
PF
0.3 to 1.0
– 40 to 125
—
7
T
J
°C
3
2
Input-Output Isolation Voltage — Maximum (2)
47–63 Hz, 1 sec Duration
V
R
3750
8.0
Vac(rms)
ISO
Thermal Resistance — Power Triac Junction to
Case (See Figure 18)
°C/W
θJC
9
1, 4, 5, 6, 8. NO PIN
2. LED CATHODE
3. LED ANODE
Ambient Operating Temperature Range
Storage Temperature Range
T
– 40 to +100
– 40 to +150
260
°C
°C
°C
oper
T
stg
7. MAIN TERMINAL 2
9. MAIN TERMINAL 1
Lead Soldering Temperature — Maximum
(1/16″ From Case, 10 sec Duration)
T
L
1. Test voltages must be applied within dv/dt rating.
2. Input-Output isolation voltage, V
(2)For this test, pins 2, 3 and the heat tab are common, and pins 7 and 9 are common.
, is an internal device dielectric breakdown rating.
ISO
POWER OPTO is a trademark of Motorola, Inc.
This document contains information on a new product. Specifications and information herein are subject to change without notice.
Preferred devices are Motorola recommended choices for future use and best overall value.
REV 1
Motorola Optoelectronics Device Data
1
Motorola, Inc. 1995