DESIGNED & DIMENSIONED
IN MILLIMETERS[INCHES]
MHXXX-XXXXX-XXXXXX-XXXX
REVISION R
FIG 2
CABLE STRIPPING DIMENSIONS
PER CONFIGURATIONS
OVERALL CABLE LENGTH
MILLIMETERS OF CABLE
0030 MIN. (SEE NOTE 8 & 9)
CABLE CALLOUT
081: CCA-081
(0.81 OD MINIATURE COAX CABLE)
113: CCA-113
(1.13 OD MINIATURE COAX CABLE)
(SEE TABLE 1)(SEE NOTES 12,13,14,15)
DO NOT
SCALE FROM
THIS PRINT
"A" mm
"B" mm
"C" mm
C
END 2 CONNECTOR OR PREPARATION
-MH1RP: MHF1-P-C-RA-CAX (SEE SHEET 2)
(081 CABLE TYPE: MHF1-P-C-RA-CA3)
(113 CABLE TYPE: MHF1-P-C-RA-CA4)
-MH3RP: MHF3-P-C-RA-CA3 (SEE SHEET 2)
(081 CABLE TYPE ONLY)
END 1 CONNECTOR
-MH1RP: MHF1-P-C-RA-CAX (SEE SHEET 2)
(081 CABLE TYPE: MHF1-P-C-RA-CA3)
(113 CABLE TYPE: MHF1-P-C-RA-CA4)
-MH3RP: MHF3-P-C-RA-CA3 (SEE SHEET 2)
(081 CABLE TYPE ONLY)
C
C
-01BJ1: SMA-J-C-X-ST-BHX (SEE SHEET 2)
(081 CABLE TYPE: SMA-J-C-X-ST-BH3)
(113 CABLE TYPE: SMA-J-C-X-ST-BH4)
-01BJ2: SMA-J-C-X-ST-BRX (SEE SHEET 2)
(081 CABLE TYPE: SMA-J-C-X-ST-BR3)
(113 CABLE TYPE: SMA-J-C-X-ST-BR4)
-01SB1: SMA-J-C-X-ST-SBX (SEE SHEET 2)
(081 CABLE TYPE: SMA-J-C-X-ST-SB3)
(113 CABLE TYPE: SMA-J-C-X-ST-SB4)
-01SR1: SMA-J-C-X-ST-SRX (SEE SHEET 2)
(081 CABLE TYPE: SMA-J-C-X-ST-SR3)
(113 CABLE TYPE: SMA-J-C-X-ST-SR4)
-SING: SINGLE ENDED (ONE END ONLY, SEE NOTE 11)
-XXXXXX: STRIPPED AND TINNED (THIS END ONLY-
SEE NOTES 11-15, 17 & SHEET 2, FIG 3)
"D" mm
"E" mm
-01BJ1: SMA-J-C-X-ST-BHX (SEE SHEET 2)
(081 CABLE TYPE: SMA-J-C-X-ST-BH3)
(113 CABLE TYPE: SMA-J-C-X-ST-BH4)
-01BJ2: SMA-J-C-X-ST-BRX (SEE SHEET 2)
(081 CABLE TYPE: SMA-J-C-X-ST-BR3)
(113 CABLE TYPE: SMA-J-C-X-ST-BR4)
-01SB1: SMA-J-C-X-ST-SBX (SEE SHEET 2)
(081 CABLE TYPE: SMA-J-C-X-ST-SB3)
(113 CABLE TYPE: SMA-J-C-X-ST-SB4)
-01SR1: SMA-J-C-X-ST-SRX (SEE SHEET 2)
(081 CABLE TYPE: SMA-J-C-X-ST-SR3)
(113 CABLE TYPE: SMA-J-C-X-ST-SR4)
(SEE FIG 2) "C" FORMAT: X.Xmm
(SEE FIG 2) "B" FORMAT: X.Xmm
(SEE FIG 2) "A" FORMAT: X.Xmm
DO NOT LEAVE ANY SPACE BLANK,
EACH POSITION MUST CONTAIN A
NUMERIC CHARACTER 0 THRU 9.
C
LENGTH: XXXX
(SEE TABLE 2 FOR TOLERANCE)
(SEE NOTE 2 FOR CABLE CUT LENGTH)
NOTES:
C
1.
REPRESENTS A CRITICAL DIMENSION.
ATTACH LABEL-ET
THIS END
2. CABLE CUT LENGTH:
= (LENGTH: XXXX) - (SUBTRACTOR FOR END 1) - (SUBTRACTOR FOR END 2).
(SEE TABLE 1 FOR SUBTRACTORS)
3. ASSEMBLY TO BE 100% TESTED FOR OPENS & SHORTS.
C
C
4. ASSEMBLY TO BE 100% HI-POT TESTED PER TABLE 1, THE TEST VOLTAGE FOR THE ASSEMBLY
SHOULD BE SET TO THE END OPTION WITH THE LOWEST TEST VOLTAGE RATING.
5. AFTER FINAL ELECTRICAL TESTS, LABEL EACH CABLE ASSEMBLY WITH 1 LABEL -ET
6. CRITICALS ON CONNECTOR PRINTS TO BE CHECKED IN PROCESS.
7. FINISHED ASSEMBLIES TO BE PACKAGED PER PACKAGING STANDARD CO-RF-WI-3040-M.
-LOCKWASHERS, NUTS, AND GASKETS TO BE SHIPPED UNASSEMBLED.
8. CABLE STOCKED IN INCHES, 1 INCH = 25.4 MILLIMETERS.
END 1
END 2
FIG 1
9. CABLE LENGTHS LONGER THAN 1000 MILLIMETERS ARE NOT SUPPORTED BY S.I. TEST DATA.
MHXXX-MH1RP-01BJ1-XXXX SHOWN
10. MINIMUM BEND RADIUS FOR MH081 = 5.0 [.20]
MH113 = 6.8 [.27]
THIS PRODUCT MANUFACTURED
WITH LEAD-FREE PROCESSING
Pb
11. FOR SING ENDED OR STRIPPED AND TINNED ASSEMBLIES: MAKE A DOUBLE ENDED
ASSEMBLY AT TWICE THE CABLE LENGTH AND TEST BEFORE CUTTING ASSEMBLY IN HALF.
12. DIM "A", "B", AND "C" HAVE A MINIMUM VALUE OF 0.0mm & A MAXIMUM VALUE OF 9.9mm.
13. PRODUCTION OF STRIP AND TIN FOR CENTER DIELECTIC USE: A.
14. PRODUCTION OF STRIP AND TIN FOR SHIELD USE: D=A+B.
15. PRODUCTION OF STRIP AND TIN FOR JACKET USE: E=A+B+C.
16. FOR -RA TO -RA, CONNECTORS SHOULD BOTH BE ORIENTED UP. (SEE SHEET 2, FIG. 4)
17. FOR STRIPPED AND TINNED OPTION, ONLY THE CENTER CONDUCTOR IS TINNED.
F:\DWG\MISC\MKTG\MHXXX-XXXXX-XXXXXX-XXXX-MKT.SLDDRW
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
MILLIMETERS [INCHES].
TOLERANCES ARE:
DECIMALS
ANGLES
2
.X: 0.3 [.01]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
.XX: 0.13 [.005]
PHONE: 812-944-6733
FAX: 812-948-5047
code 55322
.XXX: 0.051 [.0020]
e-Mail info@SAMTEC.com
MATERIAL:
SHEET SCALE: 2:1
DO NOT SCALE DRAWING
DESCRIPTION:
SEE END 1 AND END 2 ASSEMBLY PRINTS
MICRO RF CABLE ASSEMBLY
NO.
DWMG. HXXX-XXXXX-XXXXXX-XXXX
07/26/2005
CUMMINGS
SHEET 1 OF
3
BY: