19-3732; Rev 1; 8/06
Stereo Audio CODECs with Microphone, DirectDrive
Headphones, Speaker Amplifiers, or Line Outputs
General Description
Features
ꢀ +1.7V to +3.3V (Digital) and +2.6V to +3.3V
The MAX9851/MAX9853 are single-chip, stereo audio
CODECs designed to provide a complete audio solu-
tion for a GSM/GPRS/EDGE cell phone. The MAX9851/
MAX9853 provide stereo DirectDriveTM headphone
amplifiers, a mono receiver speaker amplifier, stereo
Class D speaker amplifiers (MAX9851 only), stereo dif-
ferential line outputs (MAX9853 only), microphone input
amplifiers, plus flexible input selection and gain control.
Two serial digital audio interfaces are included, one
intended to accept voiceband data and the other
accepting I2S data. The voiceband interface can be
reconfigured as needed to act as a secondary I2S feed
input—allowing multiple audio source mixing of ringer
tones or other audio at different sample rates. A trans-
ducer/vibrator signal can be derived from digital audio.
(Analog) Operation
ꢀ +2.6V to +5.5V Class D Speaker Amplifier
Operation (Direct from Battery)
ꢀ Low 26mW Quiescent Power Consumption
(Playback)
ꢀ High 98dB Power-Supply Rejection Ratio
ꢀ 8kHz to 48kHz Sample Rate (Replay and Record)
ꢀ Stereo 18-Bit ADC and DAC
ꢀ Low-Noise Stereo Microphone Inputs and Stereo
Line Inputs
ꢀ Dual Source Digital Mixing (DAC)
ꢀ Selectable Voiceband Filter for
Recording/Playback Modes
The stereo digital-to-analog converter (DAC) path
includes filtering and mixing, programmable-gain ampli-
fiers (PGA), soft muting, and optional voiceband digital
filtering. The MAX9851/MAX9853 accept up to two digital
audio inputs at different sample rates. All analog inputs
have PGAs on the front end, allowing dynamic range
optimization with a wide range of input sources.
ꢀ Digital Filtering, Soft Mute, and Volume Control
ꢀ Low-Noise, High-PSRR Microphone Bias
Generator
ꢀ Stereo DirectDrive Headphone Amplifier
(2 x 50mW)
ꢀ Mono DirectDrive Handset Receiver Amplifier
The stereo analog-to-digital converter (ADC) converts
audio signals from either internal or external microphones
or stereo line inputs. The microphone amplifiers have a
programmable gain from 0 to 40dB to handle both ampli-
fied microphones and electret modules. In addition to a
digital highpass filter to remove DC offset voltages, the
ADC also features voiceband digital filtering.
(1 x 105mW)
ꢀ Stereo Class D, Ultra-Low-EMI, Filterless Speaker
Amplifier with Active Emissions Limiting
(2 x 1.25W, 8Ω) (MAX9851)
ꢀ Stereo Differential Line Output Amplifiers
(MAX9853)
ꢀ Clickless/Popless Operation
The digital audio interfaces support a variety of serial
audio formats. The secondary serial audio interface has
an independent supply voltage to allow integration into
multiple supply systems. Control for volume levels, sig-
nal mixing, and operating modes is done through the
I2C 2-wire interface.
ꢀ Flexible Shutdown Modes for Power Saving
ꢀ Comprehensive Headset Detection
ꢀ Ultra-Low Power Wake-Up on Headset Detection
All circuitry is optimized for high PSRR. The MAX9851/
MAX9853 use a thermally efficient, space-saving 48-pin
thin QFN package (7mm x 7mm x 0.8mm) with an
exposed pad.
Ordering Information
PART
PIN-PACKAGE
PKG CODE
48 TQFN-EP**
(7mm x 7mm x 0.8mm)
MAX9851ETM+
T4877-6
Applications
GSM/GPRS/EDGE Cell Phones
48 TQFN-EP**
(7mm x 7mm x 0.8mm)
MAX9853ETM+
T4877-6
PDAs/SmartPhones
Note: All devices specified over the -40°C to +85°C temperature
range.
+Denotes lead-free package.
**EP = Exposed pad.
Pin Configurations and Selector Guide appear at end of data
sheet.
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.