19-3178; Rev 0; 2/04
Wide-Input, High-Frequency, Triple-Output Supplies
with Voltage Monitor and Power-On Reset
General Description
Features
The MAX8513/MAX8514 integrate a voltage-mode
PWM step-down DC-DC controller and two LDO con-
trollers, a voltage monitor, and a power-on reset for the
lowest-cost power-supply and monitoring solution for
xDSL modems, routers, gateways, and set-top boxes.
♦ Low-Cost DC-DC Controller with Two LDOs
♦ Wide Input Range: 4.5V to 28V
♦ 300kHz to 1.4MHz Adjustable Switching
Frequency
♦ Low Noise for High Data-Rate xDSL Applications
♦ Synchronizable to External Clock
♦ Adjustable Soft-Start
The DC-DC controller switching frequency can be set
with an external resistor from 300kHz to 1.4MHz, to allow
for the optimization of cost, size, and efficiency. For noise-
sensitive applications, the DC-DC controller can also be
synchronized to an external clock, minimizing noise inter-
ference. Operation above 1.1MHz reduces noise for high
data-rate xDSL applications. An adjustable soft-start and
adjustable foldback current limit provide reliable startup
and fault protection. The DC-DC controller output voltage
can be set externally to a voltage from 1.25V to 5.5V.
Current limiting is accomplished by inductor current sens-
ing for improved efficiency, or by an external sense resis-
tor for better accuracy.
♦ Lossless Adjustable Foldback Current Limit
♦ Power-On Reset with 140ms Delay
♦ Adjustable Input Power-Fail Warning for Dying
Gasp
♦ Selectable Output-Voltage Sequencing or
Output-Voltage Tracking
Ordering Information
The MAX8513/MAX8514s’ first LDO controller is
designed to provide a low-cost, high-current regulated
output from 0.8V to 5.5V using an N-channel MOSFET or
a low-current output using a low-cost NPN transistor. The
MAX8513’s second regulator can be used to generate
0.8V to 27V output with a low-cost PNP transistor. Both
LDO regulators can operate either from the DC-DC con-
troller output or from a higher voltage derived with a fly-
back overwinding on the DC-DC converter inductor. The
MAX8514’s second LDO regulator is designed to pro-
vide a negative output with an NPN transistor.
PART
TEMP RANGE
-40°C to +85°C
-40°C to +85°C
PIN-PACKAGE
MAX8513EEI
MAX8514EEI
MAX8514AEI
28 QSOP
28 QSOP
-40°C to +125°C 28 QSOP
Functional Diagram
V
IN
(4.5V TO 28V)
A sequence input allows the outputs to either power up
together, or for the DC-DC regulator to power up first
and each LDO controller to power up in sequence. An
input power-fail output (PFO) is provided for input
power-fail warning, such as in dying-gasp applications.
A power-on reset circuit with a 140ms delay is also
included to indicate when all outputs have achieved
regulation and stabilized.
MAX8513
ON
OFF
V
OUT1
STEP-
DOWN
(1.25V TO 5.5V)
CONTROLLER
SYNC
Applications
xDSL, Cable, ISDN Modems, and Routers
Wireless Routers
OUTPUT
POWER-ON RESET
LDO
CONTROLLER 1
V
OUT2
(0.8V TO V
)
OUT1
Set-Top Boxes
Automotive Dashboard Electronics
INPUT POWER-
FAIL MONITOR
LDO
CONTROLLER 2
V
OUT3
Pin Configurations appear at end of data sheet.
(0.8V TO 27V)
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.