Datasheet > MAX40008

MAX40008

更新时间： 2024-11-30 02:52:43

品牌	Logo	应用领域
美信 - MAXIM		/
页数	文件大小	规格书
11页	1401K
描述
300ns Propagation Delay

阅读下载

中文翻译

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

MAX40008 数据手册

MAX40008/MAX40009 Evaluation Kit

Evaluates: MAX40008/MAX40009

General Description

Quick Start

The MAX40008/MAX40009 evaluation kit (EV kit) is a

fully assembled and tested PC board that evaluates

the MAX40008/MAX40009 single comparator with shutdown

input. The MAX40009EVKIT# comes with a push-pull out-

put (MAX40009ANT+), while the MAX40008EVKIT# EV

kit comes with an open-drain output (MAX40008ANT+)

Required Equipment

● Three +5V DC power supplies

(V , V , and V

)

DD IN+

PULL

● Two digital multimeters (DMMs)

Procedure

installed that operates off a V

supply between 1.7V

The MAX40008/MAX40009 EV kit is fully assembled

and tested. Follow steps below to verify board operation.

Caution: Do not turn on the power supply until all

connections are completed.

and 5.5V. The MAX40008/MAX40009 has a wide input

common mode voltage range from -0.2V to V + 0.2V.

This EV kit demonstrates the MAX40008/MAX40009 in an

ultra-small, 0.73mm x 1.1mm, 6-bump wafer-level pack-

age (WLP) with 0.35mm bump spacing.

1) Connect the positive terminal of a DC power supply

to the VDD test point and the ground terminal to the

GND test point.

The EV kit can be used to evaluate both the

MAX40008 and MAX40009 with a 6-bump WLP. To

evaluate the MAX40008 (open-drain output version on

MAX40009EVKIT#), replace U1 (MAX40009) with the

MAX40008 with jumper J1 installed.

2) Connect the positive terminal of a DC power supply to

the VPULL test point and the ground terminal to the

GND test point when evaluating the MAX40008. This

is not necessary when evaluating the MAX40009.

When using the MAX40008EVKIT# to evaluate the

MAX40009 (push-pull version), replace U1 (MAX40008)

with MAX40009 with jumper J1 removed.

3) Connect the positive terminal of a DC power supply

to the INP test point and the ground terminal to the

GND test point.

Features

● 300ns Propagation Delay

● Wide Input Common Mode Voltage Range,

4) Turn on the V

power supply and set it to any

voltage between 1.7V and 5.5V.

5) Turn on the V power supply and set it to any

PULL

-0.2V to V

+ 0.2V

voltage between 1.7V to 5.5V (MAX40008 only).

● Hysteresis Adding Configurable

● Evaluates 6-Bump WLP Package

● Fully Assembled and Tested

Do not need V supply when MAX40009

PULL

(push-pull output) is used.

6) Turn on the IN+ power supply and set it to the desired

level.

7) Monitor the output using a DMM at the V

test

Ordering Information appears at end of data sheet.

OUT

point and observe its response to varying voltage at

IN+. V should be at logic-high (V ) when voltage

OUT

PULL

applied on IN+ is greater than V

and should be at

IN-

logic-low (0V) when the voltage applied on IN+ is less

than V

IN-

319-100005; Rev 1; 6/17

12 3 4 5 6 7...11

中文翻译

下载PDF

与MAX40008相关器件

型号	品牌	获取价格	描述	数据表
MAX40008EVKIT	MAXIM	获取价格	Hysteresis Adding Configurable
MAX40009	MAXIM	获取价格	Hysteresis Adding Configurable
MAX40009	ADI	获取价格	220ns、12μA、6焊球WLP封装比较器，带关断
MAX40009EVKIT	MAXIM	获取价格	300ns Propagation Delay
MAX4000EBL+T	MAXIM	获取价格	Log Or Antilog Amplifier, 1 Func, 2400MHz Band Width, BIPolar, UCSP-8
MAX4000EBL-T	MAXIM	获取价格	2.5GHz 45dB RF-Detecting Controllers
MAX4000EUA	MAXIM	获取价格	2.5GHz 45dB RF-Detecting Controllers
MAX4000EUA+T	MAXIM	获取价格	暂无描述
MAX4000EUA-T	MAXIM	获取价格	Log Or Antilog Amplifier, 1 Func, 2400MHz Band Width, BIPolar, PDSO8, MICRO, MO-187C-AA, S
MAX4001	MAXIM	获取价格	2.5GHz 45dB RF-Detecting Controllers

与MAX40008相关文章

解析光耦仿真器：升级光耦合器技术的必要性
2024-11-18

49
英伟达新一代Blackwell GPU过热问题致交付延迟
2024-11-18

38
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
2024-11-14

67
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
2024-11-14

63

产品中心

服务支持

精选活动

关于我们

帮助中心

MAX40008

MAX40008 数据手册

与MAX40008相关器件

与MAX40008相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

MAX40008

MAX40008 数据手册

与MAX40008相关器件

与MAX40008相关文章

您还可以找

您在本页遇到什么问题？