Pl tronics, Inc.
.
19013 36th Ave. W, Suite H Lynnwood, WA 98036 USA
Manufacturer of High Quality Frequency Control Products
LV7645D LVDS Series
Low Voltage Differential Signal Output with Enable / Disable
–
80.00 MHz 212.50 MHz
6 Pad Leadless Surface Mount Clock Oscillator
Consult factory for higher frequencies
Standard Specifications
Overall Frequency Stability
± 50 PPM, ± 25 PPM and ± 20 PPM over Operating Temp. Range
Operating Temperature Range 0 to +80°C is standard, can be extended to - 40 to +85°C
Operable Supply Voltage (Vcc) 3.3 V ± 5% standard, 2.5 V ± 5% also available
High Level Output Voltage
Low Level Output Voltage
1.43 V typical and 1.60 V maximum with output enabled (100 ohm load, R1 = 50 ohms) See Test circuit #6
0.90 V minimum and 1.10 V typical with output enabled (same conditions as above)
Differential Output Voltage
Differential Output Error
Offset Voltage
247 mV minimum, 330 mV typical and 454 mV maximum with output enabled (same conditions as above)
50 mV maximum with output enabled (same conditions as above)
1.125 V minimum, 1.25 V typical and 1.375 V maximum with output enabled (same as above)
Offset Voltage Error
Output Leakage Current
Supply Current (Icc)
Symmetry (DC1)
Symmetry (DC2)
Rise and Fall Time (Tr & Tf)
RMS Jitter
50 mV maximum with output enabled (same as above)
10 uA maximum with output disabled
35 mA typical and 47 mA maximum with output enabled, 30 uA maximum with output disabled
45/55% measured at crossing point 0°C <= Ta <= 70°C, 40/60% measured at Ta < 0°C and Ta > 70°C
45/55% measured at 50% of output swing 0°C <= Ta <= 70°C, 40/60% measured at 50% of output swing
1.5 nS max at 20% to 80% output swing (100 ohm load) See Test circuit #6 and Waveform #2
1.5 pS max at12 kHz to 20 MHz from the output
Enable / Disable Pin:
The Enable / Disable pin has an internal pull up and if the pin is not connected the oscilaltor is enabled. Pletronics strongly recommends
connecting the Enable / Disable pin to Vcc, if the oscillator is to be enabled at all times. In the disable condition, the output becomes a
high impedance and the internal oscillator circuit is inhibited (the internal circuit is stopped).
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
Low Level Input Current
Output Enable Time
0.7 Vcc minimum at Enable / Disable Pin
0.3 Vcc maximum at Enable / Disable Pin
-20 uA maximum at Enable / Disable Pin = 0.7 Vcc
-200 uA maximum at Enable / Disable Pin = 0 V
200 nS maximum at output enable or 1 mS maximum at output enabled and stable
200 nS maximum at output disable
Output Disable Time
Part Numbering Guide
Portions of the part number that appear after the frequency may not be marked on part (C of C provided)
LV76 45 D V - 100.0M - XXX (Internal Code or blank)
Packaging
Tube or
16mm tape
8mm pitch
Model
Frequency in MHz
LV76 = E/D Pin 1
LV78 = E/D Pin 2
Special Specifications (choose all that apply)
E: Extended Operating Temp Range (-40 to +85°C)
V: Supply Voltage of 3.3 volts ±5%
W: Supply Voltage of 2.5 volts ±5%
Frequency Stability
45 = ± 50 PPM
44 = ± 25 PPM
20 = ± 20 PPM
Consult factory for available frequencies and specs. Not all options available for all frequencies. A special part number may be assigned.
Frequency Stability is inclusive of frequency shifts due to calibration, temperature, supply voltage, shock, vibration and load
Jun 2004
(425) 776 -1880, Fax: (425) 776-2760, ple-sales@pletronics.com, www.pletronics.com
TBD
Pl tronics, Inc.