LTM4705
ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating
temperature range (Note 2), otherwise specifications are at TA = 25°C (Note 2), VIN1 = VIN2 = 12V, unless otherwise noted per the
typical application shown in Figure 23.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
A
I
I
Input Supply Current
V
IN1
V
IN1
V
OUT
= V = 12V, V
= 1.5V, I = 5A
OUT
0.74
S(VIN)
IN2
OUT
l
l
Output Continuous Current Range
Line Regulation Accuracy
= V = 12V, V
= 1.5V (Note 3)
0
5
A
OUT(DC)
IN2
OUT
ΔV
OUT
/
= 1.5V, V = V = 3.1V to 20V, I = 0A
OUT
0.01
0.2
8
0.1
ꢀ/V
OUT(Line)
IN1
IN2
V
l
ΔV
OUT
/
Load Regulation Accuracy
Output Ripple Voltage
Turn-On Overshoot
V
= 1.5V, I
= 0A to 5A
0.8
ꢀ
mV
mV
ms
mV
µs
OUT(Load)
OUT
OUT
OUT
V
V
I
= 0A, C
= 100µF Ceramic, V = V = 12V, V
IN1 IN2
OUT(AC)
OUT
OUT
= 1.5V
ΔV
OUT(START)
I
= 0A, C
= 100µF Ceramic, V = V = 12V, V
15
5
OUT
OUT
IN1
IN2
OUT
= 1.5V
= 100µF Ceramic, No Load, TRACK/SS = 0.01µF, V
IN
t
Turn-On Time
C
OUT
= 12V, V
START
= 1.5V
OUT
ΔV
Peak Deviation for Dynamic Load
Load: 0ꢀ to 25ꢀ to 0ꢀ of Full Load, C
= 100µF
= 100µF
30
70
OUTLS
OUT
OUT
Ceramic, V = 12V, V
= 1.5V
IN
OUT
t
Settling Time for Dynamic Load Step Load: 0ꢀ to 25ꢀ to 0ꢀ of Full Load, C
Ceramic, V = 12V, V = 1.5V
SETTLE
IN
OUT
I
Output Current Limit
Voltage at V Pin
V
= 12V, V
= 1.5V
6
A
V
OUTPK
IN
OUT
OUT
l
V
I
= 0A, V
= 1.5V
0.592
0.6
0.608
30
FB
FB
OUT
I
Current at V Pin
(Note 4)
nA
kΩ
FB
FB
R
Resistor Between V
and V Pins
60
60.4
60.8
2.6
FBHI
OUT
FB
UVLO
V
Undervoltage Lockout
V
Falling
2.2
2.4
0.5
V
V
IN
IN
Hysteresis
I
t
t
t
Track Pin Soft-Start Pull-Up Current TRACK/SS = 0V
1.4
1000
30
µA
µs
ns
ns
TRACK/SS
ss
Internal Soft-Start Time
Minimum On-Time
Minimum Off-Time
PGOOD Trip Level
10ꢀ to 90ꢀ Rise Time (Note 4)
(Note 4)
(Note 4)
ON(MIN)
OFF(MIN)
100
V
V
FB
with Respect to Set Output
FB
FB
PGOOD
V
V
Ramping Negative
Ramping Positive
–10
3.1
–8
8
–5
10
ꢀ
ꢀ
R
PGOOD Pull-Down Resistance
10mA Load
= V = 3.6V to 20V
25
3.3
1.3
Ω
V
PGOOD
INTVCC
INTVCC
V
Internal V Voltage
V
3.5
CC
IN1
IN2
V
INTV Load Regulation
I
= 0mA to 50mA
CC
ꢀ
CC
Load Reg
FREQ
Default Switching Frequency
1
MHz
V
SYNC/MODE High Threshold
SYNC/MODE Low Threshold
MODE V
MODE V
1
V
V
SYNC/MODE
IH
IL
0.3
I
SYNC/MODE Input Current
MODE = 0V
MODE = INTV
1.5
–1.5
µA
µA
MODE
CC
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
ambient temperature consistent with these specifications is determined by
specific operating conditions in conjunction with board layout, the rated
package thermal resistance and other environmental factors.
Note 3: See output current derating curves for different V , V
and T .
A
IN OUT
Note 2: The LTM4705 is tested under pulsed load conditions such that T ≈
J
Note 4: 100ꢀ tested at wafer level.
T . The LTM4705E is guaranteed to meet performance specifications over
A
Note 5: This IC includes overtemperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperature will exceed 125°C when overtemperature protection is active.
Continuous operation above the specified maximum operating junction
temperature may impair device reliability.
the 0°C to 125°C internal operating temperature range. Specifications over
the full –40°C to 125°C internal operating temperature range are assured
by design, characterization and correlation with statistical process controls.
The LTM4705I is guaranteed to meet specifications over the full –40°C
to 125°C internal operating temperature range. Note that the maximum
Rev. 0
3
For more information www.analog.com