LT1074/LT1076
Step-Down Switching
Regulator
ponents,areincludedonthechip.Thetopologyisaclassic
positive “buck” configuration but several design innova-
tions allow this device to be used as a positive-to-negative
converter, a negative boost converter, and as a flyback
converter. The switch output is specified to swing 40V
below ground, allowing the LT1074 to drive a tapped-
inductor in the buck mode with output currents up to 10A.
FEATURES
■
5A Onboard Switch (LT1074)
■
Operates Up to 60V Input
■
100kHz Switching Frequency
■
Greatly Improved Dynamic Behavior
■
Available in Low Cost 5 and 7-Lead Packages
■
Only 8.5mA Quiescent Current
The LT1074 uses a true analog multiplier in the feedback
loop. This makes the device respond nearly instanta-
neously to input voltage fluctuations and makes loop gain
independent of input voltage. As a result, dynamic behav-
ior of the regulator is significantly improved over previous
designs.
■
Programmable Current Limit
■
Micropower Shutdown Mode
U
APPLICATIO S
■
Buck Converter with Output Voltage Range of 2.5V
On-chip pulse by pulse current limiting makes the LT1074
nearlybust-proofforoutputoverloadsorshorts.Theinput
voltage range as a buck converter is 8V to 60V, but a self-
boot feature allows input voltages as low as 5V in the
inverting and boost configurations.
to 50V
■
Tapped-Inductor Buck Converter with 10A Output
at 5V
■
Positive-to-Negative Converter
■
Negative Boost Converter
■
Multiple Output Buck Converter
TheLT1074isavailableinlowcostTO-220orDDpackages
with frequency pre-set at 100kHz and current limit at 6.5A
(LT1076 = 2.6A). A 7-pin TO-220 package is also available
which allows current limit to be adjusted down to zero. In
addition, full micropower shutdown can be programmed.
See Application Note 44 for design details.
U
DESCRIPTIO
The LT®1074 is a 5A (LT1076 is rated at 2A) monolithic
bipolar switching regulator which requires only a few
external parts for normal operation. The power switch, all
oscillator and control circuitry, and all current limit com-
A fixed 5V output, 2A version is also available. See LT1076-5.
, LTC and LT are registered trademarks of Linear Technology Corporation.
U
Buck Converter Efficiency
TYPICAL APPLICATIO
LT1074
Basic Positive Buck Converter
100
L1**
50µH (LT1074)
V
= 12V, V = 20V
IN
OUT
100µH (LT1076)
90
80
5V
V
V
IN
SW
FB
5A
* USE MBR340 FOR LT1076
** COILTRONICS #50-2-52 (LT1074)
#100-1-52 (LT1076)
PULSE ENGINEERING, INC.
#PE-92114 (LT1074)
10V TO 40V
R1
2.8k
1%
LT1074
MBR745*
V
= 5V, V = 15V
IN
OUT
70
60
50
GND
V
C
#PE-92102 (LT1076)
HURRICANE #HL-AK147QQ (LT1074)
R2
2.21k
1%
R3
L = 50µH TYPE 52 CORE
DIODE = MBR735
2.7k
#HL-AG210LL (LT1076)
+
+
C3†
200µF
C2
0.01µF
C1
500µF
25V
†
RIPPLE CURRENT RATING ≥ I /2
OUT
0
1
2
3
4
5
6
OUTPUT LOAD CURRENT (A)
LT1074•TPC27
LT1074•TA01
sn1074 1074fds
1