LM2903H
7.4 ELECTRICAL CHARACTERISTICS
(At TA = +25C, VCM=(VS/2), VS=5V, unless otherwise noted.) (1)
LM2903H
TYP(3)
PARAMETER
Operating Voltage Range
Quiescent Current
CONDITIONS
UINT
MIN(2)
MAX(2)
VS
IQ
3.8
36
V
VS=5V, no load
110
180
uA
VS=36V, no load,
TA=-40C to +125C
VS=3.8V to 36V
250
4.5
5
-4.5
-5
±0.8
VOS
Input offset voltage
mV
VS=3.8V to 36V
TA=-40C to +125C
1
1
50
50
pA
nA
pA
nA
TA=25C
IB
Input Bias Current (4) (5)
Input Offset Current (4)
TA=-40C to +125C
TA=25C
50
IOS
50
TA=-40C to +125C
VS=3.8V to 36V
(V-)
(V-)
(V+)-1.5
VCM
AVD
Common-Mode Voltage Range (6)
V
VS=3.8V to 36V
(V+)-2.0
TA=-40C to +125C
VS=15V, VO=1.4V to
11.4V, RL≥15k to (V+)
Large signal differential voltage
amplification
20
100
250
V/mV
mV
Isink≤4mA, VID=-1V
350
550
VOL
IOL
Low-Level output voltage
Output Current(sinking)
Isink≤4mA, VID=-1V
TA=-40C to +125C
VO=1.5V; VID=-1V
10
20
6
mA
nA
nA
(V+) =VO=5V; VID=1V
(V+) =VO=36V; VID=1V
50
IOH-LKG High-Level Output Leakage Current
35
100
Switching Characteristics
RPU=5.1KΩ
Overdrive =10mV
RPU=5.1KΩ
Overdrive =100mV
RPU=5.1KΩ
Overdrive =10mV
RPU=5.1KΩ
Overdrive =100mV
RPU=5.1KΩ
Overdrive =10mV
0.65
0.25
0.55
0.25
1.0
VS=5V
VS=36V
VS=5V
VS=36V
TPHL
Propagation Delay H To L(7)
us
RPU=5.1KΩ
Overdrive =100mV
RPU=5.1KΩ
Overdrive =10mV
RPU=5.1KΩ
0.6
TPLH
Propagation Delay L To H(7)
0.9
0.55
Overdrive =100mV
NOTE:
(1) Electrical table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device.
(2) Limits are 100% production tested at 25°C. Limits over the operating temperature range are ensured through correlations using statistical
quality control (SQC) method.
(3) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration.
(4) This parameter is ensured by design and/or characterization and is not tested in production.
(5) Positive current corresponds to current flowing into the device.
(6) The voltage at either the input or common mode should not be allowed to negative by more that 0.3 V. The upper end of the common-
mode voltage range is (V+) – 1.5 V; however, one input can exceed Vs, and the comparator will provide a proper output state as long
as the other input remains in the common-mode range. Either or both inputs can go to 36 V without damage.
(7) High-to-low and low-to-high refers to the transition at the input.
7 / 19
www.run-ic.com