ALUMINUM ELECTROLYTIC CAPACITORS
Snap-in Terminal Type, Wide Temperature Range
GUseries
Approved by Reliability Center for Electronic
Component, Japan-Certification No. RCJ-03-24D
(160V~)
Withstanding 3000 hours application of ripple current at 105°C.
Higher production efficiency due to 4.0mm long terminal.
Low Profile
GJ
GU
Smaller
GN
Specifications
Item
Performance Characteristics
Category Temperature Range
–
40 ~ + 105°C (16 ~ 250V) , – 25 ~ +105°C (315 ~ 450V)
Voltage Range
Rated
Rated
16 ~ 450V
Capacitance Range
47~ 47000µF
Capacitance Tolerance
Leakage Current
± 20% at 120Hz, 20°C
3
I
CV(µA) (After 5 minutes' application of rated voltage) [C : Rated Capacitance (µF), V : Voltage (V)]
Measurement frequency : 120Hz, Temperature : 20°C
•
tan
δ
Rated voltage(V)
50
80 100
160~420
16
25
35
63
450
tan δ(MAX.)
0.50
0.40
0.35
0.30
0.25
0.20
0.15
0.20
Measurement frequency : 120Hz
Rated voltage (V)
16~100
4
20
160~250
3
12
315~450
Stability at Low Temperature
Endurance
Z—25°C/Z+20°C
Z—40°C/Z+20°C
8
—
Impedance ratio
ZT/Z20(MAX.)
After an application of DC voltage(in the range of rated DC
voltage even after over-lapping the specified ripple current) for
3000 hours at 105°C, capacitors meet the characteristic
requirements listed at right.
Capacitance change
tan δ
Within ±20% of initial value
200% or less of initial specified value
Initial specified value or less
Leakage current
Capacitance change
tan δ
Within ±15% of initial value
After leaving capacitors under no load at 105°C for 1000
Shelf Life
Marking
150% or less of initial specified value
Initial specified value or less
hours, they meet the characteristic requirements listed at right.
Leakage current
Printed with white color letter on dark green sleeve.
Type numbering system (Example : 200V 680µF)
Drawing
Polarity bar
1
2
3
4
5
6
7
8
9
10 11 12
Bottom plate
Sleeve
L G U 2 D 6 8 1 M H L A
Case dia. code
Configuration
φD
20
22
25
30
35
Code
Capacitance tolerance (±20%)
Rated Capacitance (680µF)
Rated voltage (200V)
Y
Z
L±2
Pressure relief vent
A
B
C
4.0±0.5
Series name
Type
+0.2
-0.1
0.8
2-2φ±0.1
+0.2
-0.1
1.5
(Terminal dimensions)
(PC board hole dimensions)
The other terminal is also available upon request.
Please refer page 195 for schematic of dimensions.
Frequency coefficient of rated ripple current
Frequency (Hz)
50
60
120
1.00
1.00
1.00
300
1.07
1.17
1.16
1k
10k
1.15
1.45
1.41
50k~
1.15
1.50
1.43
16~100V
0.88
0.81
0.77
0.90
0.85
0.82
1.15
1.32
1.30
Coeff.
160~250V
315~450V
Minimum order quantity : 50pcs.
Dimension table in next page.
CAT.8100R