Rad-Hard, 5.0V/3.3V µ-Processor Supervisory Circuits
ISL705ARH, ISL705BRH, ISL705CRH, ISL706ARH, ISL706BRH, ISL706CRH
This family of devices are radiation hardened 5.0V/3.3V
supervisory circuits that reduce the complexity required to
Features
• Electrically Screened to SMD 5962-11213
• QML Qualified per MIL-PRF-38535 Requirements
• Radiation Hardness
monitor supply voltages in microprocessor systems. These
devices significantly improve accuracy and reliability relative to
discrete solutions. Each IC provides four key functions.
1. A reset output during power-up, power-down, and brownout
conditions.
- High Dose Rate. . . . . . . . . . . . . . . . . . . . . . . . . . 100krad(Si)
2
- SEL/SEB LET . . . . . . . . . . . . . . . . . . . . . . 86MeV/mg/cm
TH
2. An independent watchdog output that goes low if the
watchdog input has not been toggled within 1.6s.
• Precision Supply Voltage Monitor
- 4.65V Threshold in the ISL705ARH/BRH/CRH
- 3.08V Threshold in the ISL706ARH/BRH/CRH
• 200ms (Typ) Reset Pulse Width
3. A precision threshold detector for monitoring a power
supply other than V
.
DD
4. An active-low manual-reset input.
- Active High, Active Low and Open Drain Options
Specifications for Rad Hard QML devices are controlled by the
Defense Supply Center in Columbus (DSCC). The SMD
numbers listed in the “Ordering Information” table on page 3
must be used when ordering.
• Independent Watchdog Timer with 1.6s (Typ) Timeout
• Precision Threshold Detector
- 1.25V Threshold in the ISL705ARH/BRH/CRH
- 0.6V Threshold in the ISL706ARH/BRH/CRH
Detailed Electrical Specifications for the ISL705ARH,
ISL705BRH, ISL705CRH, ISL706ARH, ISL706BRH and
ISL706CRH are contained in SMD 5962-11213. A “hot-link” is
provided on our website for downloading.
• Debounced TTL/CMOS Compatible Manual-Reset Input
• Reset Output Valid at V = 1.2V
DD
Applications
Related Literature
• ISL705RH Voltage Supervisory Circuit Evaluation Board
User’s Guide
• Supervisor for µ-Processors, µ-Controllers, FPGAs and DSPs
• Critical Power Supply Monitoring
• ISL706RH Voltage Supervisory Circuit Evaluation Board
User’s Guide
• Reliable Replacement of Discrete Solutions
5V POWER SUPPLY
1.4
1.2
VCC
1
2
3
4
MR
VDD
WDO
RST
WDI
PFO
8
7
6
5
NMI
RST
I/O
ISL705xRH
1.0
0.8
0.6
0.4
0.2
0
µP
165k
GND
PFI
ISL706xRH
20 40
49.9k
ISL705ARH
5V SUPERVISOR APPLICATION WITH OVERVOLTAGE PROTECTION
FIGURE 1. TYPICAL APPLICATION
-80 -60 -40 -20
0
60 80 100 120 140
TEMPERATURE (°C)
FIGURE 2. PRECISION THRESHOLD DETECTOR TEMPERATURE
CHARACTERISTICS CURVE
September 15, 2011
FN7662.0
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 |Copyright Intersil Americas Inc. 2011. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
1