DATASHEET
36V Radiation Tolerant Precision Instrumentation
Amplifier with Rail-to-Rail Output ADC Driver
ISL70517SEH
Features
The ISL70517SEH is a high performance, differential input,
single-ended output instrumentation amplifier designed for
precision analog-to-digital applications. It can operate over a
supply range of 8V (±4V) to 36V (±18V) and features a
differential input voltage range up to ±30V. The output stage
has rail-to-rail output drive capability optimized for ADC driver
applications. The output stage is powered by separate
supplies. This feature enables the output to be driven by the
same low voltage supplies powering the ADC, thereby
providing protection from high voltage signals and low voltage
digital circuits. Its versatility makes it suitable for a variety of
general purpose applications. Additional features not found in
other instrumentation amplifiers enable high levels of DC
precision and excellent AC performance.
• Rail-to-rail single-ended output ADC driver
• Low input offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30µV
• Input bias current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.2nA
• Excellent CMRR and PSRR . . . . . . . . . . . . . . . . . . . . . . 120dB
• Wide operating voltage range . . . . . . . . . . . . . . . ±4V to ±18V
• Closed loop -3dB BW 0.3MHz (AV = 1k) to 5.5MHz (AV = 0.1)
• Operating temperature range. . . . . . . . . . . .-55°C to +125°C
• Electrically screened to DLA SMD# 5962-15246
• Acceptance tested to 75krad(Si) (LDR) wafer-by-wafer
• Radiation tolerance
- Low dose rate (0.01rad(Si)/s) . . . . . . . . . . . . . . 75krad(Si)
- SEB LETTH (VS = ±18V). . . . . . . . . . . . . . . 60MeV•cm2/mg
The gain of the ISL70517SEH can be programmed from 0.1 to
10,000 via two external resistors, RIN and RFB. The gain
accuracy is determined by the matching of RIN and RFB. The
gain resistors have Kelvin sensing, which removes gain error
due to PC trace resistance. The input and output stages have
individual power supply pins, which enable input signals riding
on a high, common-mode voltage to be level-shifted to a low
voltage device, such as an A/D converter. The rail-to-rail output
stage can be powered from the same supplies as the ADC,
which preserves the ADC maximum input dynamic range and
eliminates ADC input overdrive.
Applications
• ADC driver
• Precision test and measurement
• High voltage process control
• Signal conditioning for remote powered sensors
• Satellite communication
Related Literature
• For a full list of related documents, visit our website
- ISL70517SEH product page
The ISL70517SEH is offered in a 24 Ld ceramic flatpack
package with an operating temperature range of -55°C to
+125°C.
SIGNAL WITH
+18V
HIGH VCM
IN+
VCC
+RIN
GAIN = 10
5V
VCO
RIN
V
+VFB
-RIN
ISL70517SEH
CC
CH 1
VOUT
+RFB
VREF
VEO
RFB
-RFB
VEE
V
IN-
CC
-18V
+18V
HIGH V
IN
SIGNAL
IN
RHADC
GND
5V
V
REF
IN+
VCC
GAIN = 0.1
+VFB
+RIN
VCO
RIN
-RIN
CH 16
ISL70517SEH
VOUT
+RFB
VREF
VEO
GND
RFB
ISL71090SEH25
-RFB
VEE
IN-
18V
ISL71090SEH25
FIGURE 1. COMPLETE SPACE GRADE ANALOG SIGNAL CHAIN
December 15, 2016
FN8699.4
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas LLC 2015, 2016. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
1