ISL6552
®
Data Sheet
July 2004
FN4918.2
Microprocessor CORE Voltage Regulator
Multi-Phase Buck PWM Controller
Features
• Multi-Phase Power Conversion
The ISL6552 multi-phase PWM control IC together with its
companion gate drivers, the HIP6601, HIP6602 or HIP6603
and external Intersil MOSFETs provides a precision voltage
regulation system for advanced microprocessors.
• Precision Channel Current Sharing
- Loss Less Current Sampling - Uses r
DS(ON)
• Precision CORE Voltage Regulation
Multi-phase power conversion is a marked departure from
earlier single phase converter configurations previously
employed to satisfy the ever increasing current demands of
modern microprocessors. Multi-phase converters, by
distributing the power and load current results in smaller and
lower cost transistors with fewer input and output capacitors.
These reductions accrue from the higher effective
conversion frequency with higher frequency ripple current
due to the phase interleaving process of this topology. For
example, a three phase converter operating at 350kHz will
have a ripple frequency of 1.05MHz. Moreover, greater
converter bandwidth of this design results in faster response
to load transients.
- ±1% System Accuracy Over Temperature
• Microprocessor Voltage Identification Input
- 5-Bit VID Input
- 1.05V to 1.825V in 25mV Steps
- Programmable “Droop” Voltage
• Fast Transient Recovery Time
• Over Current Protection
• Automatic Selection of 2, 3, or 4 Phase Operation
• High Ripple Frequency (Channel Frequency) Times
Number Channels . . . . . . . . . . . . . . . . . .100kHz to 6MHz
• QFN Package:
Outstanding features of this controller IC include
- Compliant to JEDEC PUB95 MO-220
programmable VID codes from the microprocessor that
range from 1.05V to 1.825V with a system accuracy of ±1%.
Pull up currents on these VID pins eliminates the need for
external pull up resistors. In addition “droop” compensation,
used to reduce the overshoot or undershoot of the CORE
voltage, is easily programmed with a single resistor.
QFN - Quad Flat No Leads - Package Outline
- Near Chip Scale Package footprint, which improves
PCB efficiency and has a thinner profile
• Pb-free available
Another feature of this controller IC is the PGOOD monitor
circuit which is held low until the CORE voltage increases,
during its Soft-Start sequence, to within 10% of the
Ordering Information
o
PART NUMBER TEMP. ( C)
PACKAGE
PKG. DWG. #
M20.3
programmed voltage. Over-voltage, 15% above programmed
CORE voltage, results in the converter shutting down and
turning the lower MOSFETs ON to clamp and protect the
microprocessor. Under voltage is also detected and results
in PGOOD low if the CORE voltage falls 10% below the
programmed level. Over-current protection reduces the
regulator RMS output current to 41% of the programmed
over-current trip value. These features provide monitoring
and protection for the microprocessor and power system.
ISL6552CB
0 to 70
0 to 70
20 Ld SOIC
ISL6552CBZ
(See Note)
20 Ld SOIC
(Pb-free)
M20.3
ISL6552CR
0 to 70
0 to 70
20 Ld 5x5 QFN L20.5x5
ISL6552CRZ
(See Note)
20 Ld 5x5 QFN L20.5x5
(Pb-free)
*Add “-T” suffix to part number for tape and reel packaging.
NOTE: Intersil Pb-free products employ special Pb-free material
sets; molding compounds/die attach materials and 100% matte tin
plate termination finish, which is compatible with both SnPb and
Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed
the Pb-free requirements of IPC/JEDEC J Std-020B.
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2003, 2004. All Rights Reserved.
All other trademarks mentioned are the property of their respective owners.