REVISION X
IPBD-XX-D-X
((No OF POSITIONS x .1650) + .0400)
OPTION
.012
.002
No OF POSITIONS
-02 THRU -15
(PER ROW)
-R: RETENTION LATCH
(SEE SHEET 3, FIG 3)
(SEE NOTE 16)
-K: KEYED POLARIZATION
(SEE FIG. 5 & 6,
.060
DO NOT
SCALE FROM
THIS PRINT
.095±.010
.075±.010
[SEE FIG. 2 FOR -02 POSITION]
SHEET 4)
.485
ROW SPECIFICATION
-D: DOUBLE
.773±.006
.15
NOTES:
1.
REPRESENTS A CRITICAL DIMENSION.
2. SAMTEC LOGO SHALL APPEAR AT ONE LOCATION ON SURFACE SHOWN,
APPROXIMATELY .15 x .09 (BOTH SIDES).
3. ALL MULTIPLE CAVITY MOLDS SHALL IDENTIFY EACH CAVITY WITH
TOOL DEPENDANT CAVITY ID AT THE DISCRETION OF SAMTEC ENGINEERING.
4. ALL IDENTIFICATION MARKS MUST NOT STAND GREATER THAN .002 OFF THE
SURFACE OF THE PART.
5. MOLDED SURFACES SHALL BE CONSISTENT AND SMOOTH. SURFACES TO BE
FREE OF SCATCHES, NICKS, SINK AREAS, VOIDS OR OTHER BLEMISHES.
6. MAX ALLOWABLE BOW: SEE TABLE 1.
7. PART TO BE SYMMETRIC ABOUT THE CENTERLINE WITHIN +/-.001, UNLESS
OTHERWISE STATED.
8. NUMBER OF POSITIONS (PER ROW) TO BE SHOWN ON THIS SURFACE, SIZE
AND DEPTH SIMILAR TO POSITION 1INDICATOR.
9. GATE PAD MUST BE RECESSED .005. GATE LOCATION IS AT THE MOLDERS DISCRETION.
10. END CORES ARE POLARIZED. CONFIRM GEOMETRY RELATIVE TO POSITION 1
INDICATOR & GATE PAD.
.100
(NO DRAFT)
SEE NOTE 11
((No OF POSITIONS -1) x .1650)
.0050
.0050
.1025±.0020
S/S BOW SEE TABLE 1
'G'
02
01
+.0075
-.0000
.478
"A"
+.0015
-.0050
.1650
.378
11. POSITION 1 INDICATOR TO BE .0005 MAX DEPTH.
12. EACH POSITION TO BE IDENTIFIED WHERE SHOWN.
13. .0005 MAX MISMATCH PERMISSIBLE (ALL FOUR SIDES).
14. LATCH MUST CYCLE 10 TIMES WITHOUT EVIDENCE OF CRACKING
OR COMPROMISE OF FUNCTION.
09
'B'
15. CHECK THIS FEATURE WITH GO/NOGO GAUGE.
"A"
MAX DRAFT (TYP)
16. OPTION NOT FOR SALE. FOR RETENTION LATCH FEATURE, SEE IPBD-XX-D-ML PRINT.
17. POSITION INDICATOR NOT PRESENT ON 2 & 3 POSITION -R OPTION BODIES.
'A'
FIG 1
1
IPBD-08-D SHOWN
1
MAX DRAFT (TYP)
SEE NOTE 13
"B"
'E
'C'
SEE NOTE 8
.045
30°
(TYP)
+.005
-.002
.480
PARTING LINE
'H'
.280
'D'
T/B BOW SEE TABLE 1
SEE NOTE 2
"B"
DETAIL 'H'
SCALE 15 : 1
.100
.070
SEE NOTE 3
SECTION "A"-"A"
SECTION "B"-"B"
SEE NOTE 12
PROPRIETARY NOTE
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
'F'
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DECIMALS
ANGLES
5
16
08
10
02
15
09
01
11
03
14
06
.XX: .01 [.3]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322
.XXX: .003 [.08]
.XXXX: .0015 [.038]
SHEET SCALE: 1.5:1
MATERIAL:
DO NOT SCALE DRAWING
DESCRIPTION:
.165 SHROUDED CONTACT BODY
VALOX 457, COLOR NATURAL
05
04
07
DWG. NO.
MAX REGRIND: 0%
MAX FLASH ALLOWED: .003
MAX GATE VESTIGE: .004
IPBD-XX-D-X
BY:
DEAN P
10-24-2001 SHEET 1 OF 4
F:\DWG\MISC\MKTG\IPBD-XX-D-X-MKT.SLDDRW