Datasheet > ICS280GI-XX

ICS280GI-XX

更新时间： 2024-02-29 17:25:19

品牌	Logo	应用领域
艾迪悌 - IDT		时钟光电二极管外围集成电路晶体
页数	文件大小	规格书
10页	219K
描述
Clock Generator, 200MHz, CMOS, PDSO16, 0.173 INCH, TSSOP-16

阅读下载

中文翻译

获取价格

技术参数
数据手册

如果您发现信息不准确，欢迎纠错

ICS280GI-XX 技术参数

是否Rohs认证：	不符合	生命周期：	Obsolete
零件包装代码：	TSSOP	包装说明：	TSSOP,
针数：	16	Reach Compliance Code：	compliant
ECCN代码：	EAR99	HTS代码：	8542.39.00.01
风险等级：	5.23	JESD-30 代码：	R-PDSO-G16
JESD-609代码：	e0	长度：	5 mm
湿度敏感等级：	1	端子数量：	16
最高工作温度：	85 °C	最低工作温度：	-40 °C
最大输出时钟频率：	200 MHz	封装主体材料：	PLASTIC/EPOXY
封装代码：	TSSOP	封装形状：	RECTANGULAR
封装形式：	SMALL OUTLINE, THIN PROFILE, SHRINK PITCH	峰值回流温度（摄氏度）：	240
主时钟/晶体标称频率：	166 MHz	认证状态：	Not Qualified
座面最大高度：	1.2 mm	最大供电电压：	3.465 V
最小供电电压：	3.135 V	标称供电电压：	3.3 V
表面贴装：	YES	技术：	CMOS
温度等级：	INDUSTRIAL	端子面层：	TIN LEAD
端子形式：	GULL WING	端子节距：	0.65 mm
端子位置：	DUAL	处于峰值回流温度下的最长时间：	20
宽度：	4.4 mm	uPs/uCs/外围集成电路类型：	CLOCK GENERATOR, OTHER
Base Number Matches：	1

ICS280GI-XX 数据手册

ICS280

TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER

EPROM CLOCK SYNTHESIZER

The ICS280 also provides separate output divide values,

from 2 through 63, to allow the two output clock banks to

support widely differing frequency values from the same

PLL.

External Components

The ICS280 requires a minimum number of external

components for proper operation.

Each output frequency can be represented as:

Series Termination Resistor

Clock output traces over one inch should use series

termination. To series terminate a 50Ω trace (a commonly

used trace impedance), place a 33Ω resistor in series with

the clock line, as close to the clock output pin as possible.

The nominal impedance of the clock output is 20Ω.

----

OutputFreq = REFFreq ⋅

Output Drive Control

Decoupling Capacitors

The ICS270 has two output drive settings. Low drive should

be selected when outputs are less than 100 MHz. High drive

should be selected when outputs are greater than 100 MHz.

(Consult the AC Electrical Characteristics for output rise and

fall times for each drive option.)

As with any high-performance mixed-signal IC, the ICS280

must be isolated from system power supply noise to perform

optimally.

Decoupling capacitors of 0.01µF must be connected

between each VDD and the PCB ground plane. For

optimum device performance, the decoupling capacitor

should be mounted on the component side of the PCB.

Avoid the use of vias on the decoupling circuit.

ICS VersaClock Software

ICS applies years of PLL optimization experience into a user

friendly software that accepts the user’s target reference

clock and output frequencies and generates the lowest jitter,

lowest power configuration, with only a press of a button.

The user does not need to have prior PLL experience or

determine the optimal VCO frequency to support multiple

output frequencies.

Crystal Load Capacitors

The device crystal connections should include pads for

small capacitors from X1 to ground and from X2 to ground.

These capacitors are used to adjust the stray capacitance of

the board to match the nominally required crystal load

capacitance. Because load capacitance can only be

increased in this trimming process, it is important to keep

stray capacitance to a minimum by using very short PCB

traces (and no vias) been the crystal and device. Crystal

capacitors must be connected from each of the pins X1 and

X2 to ground.

VersaClock software quickly evaluates accessible VCO

frequencies with available output divide values and provides

an easy to understand, bar code rating for the target output

frequencies. The user may evaluate output accuracy,

performance trade-off scenarios in seconds.

Spread Spectrum Modulation

The value (in pF) of these crystal caps should equal (C -6

The ICS280 utilizes frequency modulation (FM) to distribute

energy over a range of frequencies. By modulating the

output clock frequencies, the device effectively lowers

energy across a broader range of frequencies; thus,

lowering a system’s electromagnetic interference (EMI). The

modulation rate is the time from transitioning from a

minimum frequency to a maximum frequency and then back

to the minimum.

pF)*2. In this equation, C = crystal load capacitance in pF.

Example: For a crystal with a 16 pF load capacitance, each

crystal capacitor would be 20 pF [(16-6) x 2] = 20.

ICS280 Configuration Capabilities

The architecture of the ICS280 allows the user to easily

configure the device to a wide range of output frequencies,

for a given input reference frequency.

Spread Spectrum Modulation can be applied as either

“center spread” or “down spread”. During center spread

modulation, the deviation from the target frequency is equal

in the positive and negative directions. The effective

average frequency is equal to the target frequency. In

The frequency multiplier PLL provides a high degree of

precision. The M/N values (the multiplier/divide values

available to generate the target VCO frequency) can be set

within the range of M = 1 to 1024 and N = 1 to 32,895.

IDT™ / ICS™ TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER 3

ICS280

REV D 061306

1 234 5 6 7...10

中文翻译

下载PDF

与ICS280GI-XX相关器件

型号	品牌	描述	获取价格	数据表
ICS280GI-XXT	IDT	Clock Generator, 200MHz, CMOS, PDSO16, 0.173 INCH, TSSOP-16	获取价格
ICS280G-XX	IDT	Clock Generator, 200MHz, CMOS, PDSO16, 0.173 INCH, TSSOP-16	获取价格
ICS280G-XXT	IDT	Clock Generator, 200MHz, CMOS, PDSO16, 0.173 INCH, TSSOP-16	获取价格
ICS280PG	IDT	Clock Generator, 200MHz, CMOS, PDSO16, 0.173 INCH, TSSOP-16	获取价格
ICS280PG	ICSI	Package Outline and Package Dimensions (16-pin TSSOP,173 Mil. Body)	获取价格
ICS280PGI	ICSI	Package Outline and Package Dimensions (16-pin TSSOP,173 Mil. Body)	获取价格

与ICS280GI-XX相关文章

深入解析CS8416引脚说明、参数、技术特点
2024-06-03

1
TPA3116D2功放芯片参数详解、引脚说明
2024-06-03

4
移位寄存器74HC165引脚说明、驱动程序示例解读
2024-06-03

2
深入解析AD9833：DDS频率合成器的卓越性能与广泛应用
2024-06-03

2

产品中心

服务支持

精选活动

关于我们

帮助中心

ICS280GI-XX

ICS280GI-XX 技术参数

ICS280GI-XX 数据手册

与ICS280GI-XX相关器件

与ICS280GI-XX相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

ICS280GI-XX

ICS280GI-XX 技术参数

ICS280GI-XX 数据手册

与ICS280GI-XX相关器件

与ICS280GI-XX相关文章

您还可以找

您在本页遇到什么问题？