HIP6019
Data Sheet
April 1998
File Number 4490.2
Advanced Dual PWM and Dual Linear
Power Control
Features
• Provides 4 Regulated Voltages
The HIP6019 provides the power control and protection for four
output voltages in high-performance microprocessor and
computer applications. The IC integrates two PWM controllers,
a linear regulator and a linear controller as well as the
monitoring and protection functions into a single 28 lead SOIC
package. One PWM controller regulates the microprocessor
core voltage with a synchronous-rectified buck converter, while
the second PWM controller supplies the computer’s 3.3V power
with a standard buck converter. The linear controller regulates
power for the GTL bus and the linear regulator provides power
for the clock driver circuits.
- Microprocessor Core, I/O, Clock Chip and GTL Bus
• Drives N-Channel MOSFETs
• Operates from +5V and +12V Inputs
• Simple Single-Loop Control Designs
- Voltage-Mode PWM Control
• Fast Transient Response
- High-Bandwidth Error Amplifiers
- Full 0% to 100% Duty Ratios
• Excellent Output Voltage Regulation
The HIP6019 includes an Intel-compatible, TTL 5-input digital-
to-analog converter (DAC) that adjusts the core PWM output
- Core PWM Output: ±1% Over Temperature
- I/O PWM Output: ±2% Over Temperature
- Other Outputs: ±2.5% Over Temperature
voltage from 2.1V
to 3.5V
in 0.1V increments and from
in 0.05V steps. The precision reference
DC
DC
1.8V
DC
to 2.05V
DC
and voltage-mode control provide ±1% static regulation. The
second PWM controller is user-adjustable for output levels
between 3.0V and 3.5V with ±2% accuracy. The adjustable
linear regulator uses an internal pass device to provide 2.5V
±2.5%. The adjustable linear controller drives an external N-
Channel MOSFET to provide 1.5V ±2.5%.
• TTL-Compatible 5-Bit Digital-to-Analog Core Output
Voltage Selection
- Wide Range . . . . . . . . . . . . . . . . . . . 1.8V
- 0.1V Steps . . . . . . . . . . . . . . . . . . . . 2.1V
to 3.5V
to 3.5V
DC
DC
DC
DC
DC
- 0.05V Steps . . . . . . . . . . . . . . . . . . 1.8V
to 2.05V
DC
The HIP6019 monitors all the output voltages. A single Power
Good signal is issued when the core is within ±10% of the DAC
setting and the other levels are above their under- voltage
levels. Additional built-in over-voltage protection for the core
output uses the lower MOSFET to prevent output voltages
above 115% of the DAC setting. The PWM controller’s over-
current functions monitor the output current by sensing the
• Power-Good Output Voltage Monitor
• Microprocessor Core Voltage Protection Against Shorted
MOSFET
• Over-Voltage and Over-Current Fault Monitors
- Does Not Require Extra Current Sensing Element,
Uses MOSFET’s r
DS(ON)
voltage drop across the upper MOSFET’s r
, eliminating
DS(ON)
the need for a current sensing resistor.
• Small Converter Size
- Constant Frequency Operation
Pinout
- 200kHz Free-Running Oscillator; Programmable from
50kHz to 1MHz
HIP6019 (SOIC)
TOP VIEW
Applications
UGATE2
PHASE2
VID4
1
2
3
4
5
6
7
8
9
28 V
CC
•
27 UGATE1
26 PHASE1
25 LGATE1
24 PGND
23 OCSET1
22 VSEN1
21 FB1
Full Motherboard Power Regulation for Computers
• Low-Voltage Distributed Power Supplies
VID3
VID2
Ordering Information
VID1
o
PART NUMBER
TEMP. ( C)
PACKAGE
PKG. NO.
VID0
HIP6019CB
0 to 70
28 Ld SOIC
M28.3
PGOOD
OCSET2
HIP6019EVAL1
Evaluation Board
20 COMP1
19 FB3
FB2 10
COMP2 11
SS 12
18 GATE3
17 GND
FAULT/RT 13
FB4 14
16 VOUT4
15 VSEN2
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
2-252