HIP0045
Data Sheet
April 1999
File Number 4047.2
1A/50V Octal Low Side Power Driver With
Serial Bus Control and Fault Protection
Features
• Octal NDMOS Output Drivers in a High Voltage Power
BiMOS Process
The HIP0045 is a logic controlled, eight channel Octal Serial
Power Low Side Driver. The serial peripheral interface (SPI)
utilized by the HIP0045 is a serial synchronous bus compatible
with Intersil CDP68HC05, or equivalent, microcomputers. As
shown in the Block Diagram for the HIP0045, each of the open
drain MOS Output Drivers have individual protection for over-
voltage and over-current. Each output channel has separate
output latch control with fault unlatch and diagnostic or status
feedback. Under normal ON conditions, each output driver is in
a low voltage, high current state of saturated turn-on.
• Over-Stress Protection - Each Output:
- Over-Current Protection . . . . . . . . . . . . . . . . . . . 1A Min
- Over-Voltage Clamp Protection . . . . . . . . . . . . 50V Typ
- Thermal Shutdown Protection (2 Channels)
• Open-Load Detection
• Power BiMOS Output Configuration
- Current Latch-Off Protection for 6 Channels; 2 with
External Drive Input and ORed with SPI Bus Control
Comparators in the diagnostic circuitry monitor the output
drivers to determine if an out of saturation condition exists. If a
fault is sensed, the respective output driver for Channels 0 - 5
have overcurrent latch-off. Channels 6 and 7 are configured for
lamp drivers and have current limiting with over-temperature
latch-off. Channels 0 and 1 have direct parallel drive control for
PWM applications and are ORed with the SPI Bus control. All
channels are SPI Bus controlled and sense the output states
for diagnostic feedback.
- 2 Channels Configured for Lamp Drivers with Current
Limiting and Over-Temperature Latch-Off
• High Speed CMOS Logic Control
- SPI Bus Controlled Interface
- Individual Output Latch
- Individual Fault Unlatch and Feedback
- Common Reset Line
• Low Quiescent Current . . . . . . . . . . . . . . . . . . . 5mA Max
The HIP0045 is fabricated in a Power BiMOS IC process,
and is intended for use in automotive and other applications
having a wide range of temperature and electrical stress
conditions. It is particularly suited for driving relays,
solenoids and lamps in applications where low standby
power, high operating voltage, and high output current in
high ambient temperature conditions is required.
o
o
• Ambient Operating Temp. Range . . . . . . . -40 C to 125 C
Applications
• Automotive and Industrial Systems
• Solenoids, Relays and Lamp Drivers
• Logic and µP Controlled Drivers
• Robotic Controls
The HIP0045 is in a 20 lead plastic Power SOP (PSOP)
Package with an integral copper ‘slug’ to conduct heat directly
to a PCB interface or heat sink on the bottom of the package.
Pinout
Ordering Information
PART NO. TEMP. RANGE ( C)
HIP0045 (PSOP WITH HEAT SLUG)
TOP VIEW
o
PACKAGE
PKG. NO.
INTEGRAL COPPER
HEAT SINK ‘SLUG’
FOR PCB CONTACT
OR EXT. HEAT SINK
HIP0045AB
-40 to 125
20 Ld PSOP
M20.433
Driver Block Diagram
GND
CE
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
GND
IN0
OUT
RESET
OUT7
OUT5
OUT3
OUT1
MISO
OUT0
OUT2
OUT4
OUT6
MOSI
SCK
I
SK
DRIVER
OC LIMIT
(CH. 6, 7)
V
CC
SPI AND
DIRECT
INPUT
CONTROL
WITH
FAULT/
STATUS
OUTPUT
IN1
GND
OC LATCH
(CH. 0-5)
-
V
CC
+
GND
OC
REF
OVER-TEMP.
DET. (CH. 6, 7)
+
-
V
REF
FAULT/STATUS
RESET
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
4-1