HI5741
Electrical Specifications AV , DV = -4.94V to -5.46V, V = +4.75 to +5.25V, V = Internal,
REF
EE
EE
CC
T
= +25°C (Continued)
A
HI5741BI
T
= -40°C TO +85°C
A
PARAMETER
TEST CONDITIONS
MIN
TYP
86
85
77
74
73
71
76
MAX
UNITS
dBc
dBc
dBc
dBc
dBc
dBc
dBc
Spurious Free Dynamic Range to Nyquist
(Note 4)
f
f
f
f
f
f
= 10 MSPS, f
= 10 MSPS, f
= 25 MSPS, f
= 50 MSPS, f
= 75 MSPS, f
= 1.023MHz, 5MHz Span
= 2.02MHz, 5MHz Span
= 2.02MHz, 12.5MHz Span
= 5.055MHz, 25MHz Span
= 7.52MHz, 37.5MHz Span
-
-
-
-
-
-
-
-
-
-
-
-
-
-
CLK
CLK
CLK
CLK
CLK
CLK
OUT
OUT
OUT
OUT
OUT
= 100 MSPS, f
= 10.1MHz, 50MHz Span
OUT
Multi-Tone Power Ratio
(MTPR)
8 Tones, no Clipping, 110kHz Spacing, 220kHz spacing
between tones 4 and 5, f
= 20 MSPS (Note 7)
CLK
REFERENCE/CONTROL AMPLIFIER
Internal Reference Voltage, V
(Note 5)
(Note 4)
(Note 4)
-1.27
-
-1.23
50
-1.17
-
V
REF
Internal Reference Voltage Drift
µV/°C
µA
Internal Reference Output Current Sink/Source
Capability
-500
-
+50
Internal Reference Load Regulation
Amplifier Input Impedance
I
= 0 to I
REF
= -500µA
-
-
-
-
-
-
100
3
-
-
-
-
-
-
µV
MΩ
REF
(Note 4)
Amplifier Large Signal Bandwidth
Amplifier Small Signal Bandwidth
Reference Input Impedance (CTL IN)
Reference Input Multiplying Bandwidth (CTL IN)
4.0V
1.0V
Sine Wave Input, to Slew Rate Limited (Note 4)
Sine Wave Input, to -3dB Loss (Note 4)
1
MHz
MHz
kΩ
P-P
P-P
5
(Note 4)
12
75
R
= 50Ω, 100mV Sine Wave, to -3dB Loss at I
MHz
L
OUT
(Note 4)
DIGITAL INPUTS (D9-D0, CLK, INVERT)
Input Logic High Voltage, V
(Note 5)
(Note 5)
(Note 5)
(Note 5)
(Note 4)
2.0
-
-
V
IH
Input Logic Low Voltage, V
-
-
-
-
-
-
0.8
400
700
-
V
IL
Input Logic Current, I
Input Logic Current, I
µA
µA
pF
IH
IL
-
Digital Input Capacitance, C
3.0
IN
TIMING CHARACTERISTICS
Data Setup Time, t
See Figure 1 (Note 4)
See Figure 1 (Note 4)
See Figure 1 (Note 4)
See Figure 1 (Note 4)
3
0.5
-
2.0
0.25
4.5
-
-
-
-
ns
ns
ns
ns
SU
Data Hold Time, t
HLD
Propagation Delay Time, t
PD
CLK Pulse Width, t
, t
PW1 PW2
1.0
0.85
POWER SUPPLY CHARACTERISTICS
IV
IV
IV
(Note 5)
(Note 5)
(Note 5)
(Note 5)
-
-
-
-
-
42
75
13
650
5
50
95
20
-
mA
mA
EEA
EED
CCD
mA
Power Dissipation
Power Supply Rejection Ratio
NOTES:
mW
µA/V
V
±5%, V ±5%
EE
-
CC
2. Dissipation rating assumes device is mounted with all leads soldered to printed circuit board.
3. Gain Error measured as the error in the ratio between the full scale output current and the current through R
ratio should be 16.
(typically 1.28mA). Ideally the
SET
4. Parameter guaranteed by design or characterization and not production tested.
5. All devices are 100% tested at +25°C.
6. Dynamic Range must be limited to a 1V swing within the compliance range.
7. In testing MTPR, tone frequencies ranged from 1.95MHz to 3.05MHz. The ratio is measured as the range from peak power to peak distortion in
the region of removed tones.
FN4071.12
September 20, 2006
4