HI-574A, HI-674A
TM
Data Sheet
June 2001
File Number 3096.5
Complete, 12-Bit A/D Converters with
Microprocessor Interface
Features
• Complete 12-Bit A/D Converter with Reference and Clock
• Full 8-Bit, 12-Bit or 16-Bit Microprocessor Bus Interface
• Bus Access Time . . . . . . . . . . . . . . . . . . . . . . . . . . . 150ns
• No Missing Codes Over Temperature
itle
I-
4A,
-
4A,
-
4)
The HI-X74(A) is a complete 12-bit, Analog-to-Digital
Converter, including a +10V reference clock, three-state
outputs and a digital interface for microprocessor control.
Successive approximation conversion is performed by two
monolithic dice housed in a 28 lead package. The bipolar
analog die features the Intersil Dielectric Isolation process,
which provides enhanced AC performance and freedom
from latch-up.
• Minimal Setup Time for Control Signals
• Fast Conversion Times
- HI-574A (Max) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25µs
- HI-674A (Max) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15µs
• Low Noise, via Current-Mode Signal Transmission
Between Chips
bjec
Custom design of each IC (bipolar analog and CMOS digital)
has yielded improved performance over existing versions of
this converter. The voltage comparator features high PSRR
plus a high speed current-mode latch, and provides precise
decisions down to 0.1 LSB of input overdrive. More than 2X
reduction in noise has been achieved by using current
instead of voltage for transmission of all signals between the
analog and digital ICs. Also, the clock oscillator is current
controlled for excellent stability over temperature.
omp
e,
-Bit
D
nver
s
• Byte Enable/Short Cycle (A Input)
O
- Guaranteed Break-Before-Make Action, Eliminating Bus
Contention During Read Operation. Latched by Start
Convert Input (To Set the Conversion Length)
• Supply Voltage . . . . . . . . . . . . . . . . . . . . . . 12V to 15V
th
crop
esso
Applications
The HI-X74(A) offers standard unipolar and bipolar input
ranges, laser trimmed for specified linearity, gain and offset
accuracy. The low noise buried zener reference circuit is
trimmed for minimum temperature coefficient.
• Military and Industrial Data Acquisition Systems
• Electronic Test and Scientific Instrumentation
• Process Control Systems
erfa
Power requirements are +5V and 12V to 15V, with typical
dissipation of 385mW (HI-574A/674A) at 12V.
utho
)
eyw
s
Pinout
(PDIP, SBDIP)
TOP VIEW
tersi
+5V SUPPLY, V
LOGIC
28
27
26
25
24
23
22
21
20
19
18
17
16
15
1
2
STATUS, STS
DB11 MSB
DB10
DATA MODE SEL, 12/8
rpor
on,
ico
ucto
/D,
C,
3
CHIP SEL, CS
BYTE ADDR/SHORT
4
DB9
CYCLE, A
O
5
DB8
READ/CONVERT, R/C
CHIP ENABLE, CE
6
DB7
DIGITAL
+12V/+15V SUPPLY, V
CC
7
DATA
DB6
DB5
DB4
DB3
DB2
DB1
DB0
OUTPUTS
8
+10V REF, REF OUT
ANALOG
COMMON, AC
9
sh,
10
11
12
13
14
REFERENCE INPUT
nver
, bit,
le
-12V/-15V SUPPLY, V
EE
BIPOLAR OFFSET
BIP OFF
10V INPUT
LSB
dem
DIG COMMON,
DC
20V INPUT
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil and Design is a trademark of Intersil Americas Inc. | Copyright © Intersil Americas Inc. 2001
1