5秒后页面跳转
捷配首页

Datasheet > GLLA01A2B
GLLA01A2B PDF预览

GLLA01A2B

更新时间： 2024-11-28 14:50:31
品牌 Logo 应用领域
霍尼韦尔 - HONEYWELL 开关光电二极管
页数 文件大小 规格书
5页 491K
描述
Snap Acting/Limit Switch, SPDT, Momentary, 10A, 250VDC, Screw Terminal, Roller Type Actuator, Panel Mount, ROHS COMPLIANT

阅读下载

中文翻译

获取价格

GLLA01A2B 技术参数

是否无铅：不含铅是否Rohs认证：符合
生命周期：Active包装说明：ROHS COMPLIANT
Reach Compliance Code：compliantECCN代码：EAR99
HTS代码：8536.50.70.00风险等级：2.32
Is Samacsys：N执行器类型：ROLLER TYPE
主体宽度：31 mm主体高度：30.5 mm
主体长度或直径：62 mm触点（交流）最大额定R负载：10A@300VAC
最大触点电流（交流）：10 A最大触点电流（直流）：10 A
触点（直流）最大额定R负载：10A@250VDC最大触点电压（交流）：300 V
最大触点电压（直流）：250 V安装特点：PANEL MOUNT
最大操作力：12 N最高工作温度：80 °C
最低工作温度：-10 °C密封：IP66
表面贴装：NO开关动作：MOMENTARY
开关功能：SPDT开关类型：SNAP ACTING/LIMIT SWITCH
端接类型：SCREWBase Number Matches：1

GLLA01A2B 数据手册

 浏览型号GLLA01A2B的Datasheet PDF文件第2页浏览型号GLLA01A2B的Datasheet PDF文件第3页浏览型号GLLA01A2B的Datasheet PDF文件第4页浏览型号GLLA01A2B的Datasheet PDF文件第5页 
ISSUE 3  
Installation Instructions for the  
GLL Series Limit Switch  
50012101  
POSITIONING LEVER  
WARNING  
The lever on rotary actuated units is adjustable to any of  
the segmented positions 360° around the shaft;  
however, the degree of rotation is dependant on head  
position and direction of roller.  
1. Loosen the lever retaining screw with a Phillips head  
screwdriver.  
2. Remove lever.  
3. Reposition lever to desired location.  
4. Securely tighten screw.  
PERSONAL INJURY  
• Where possible, install these switches with the  
conduit opening pointed down to drain moisture away  
from switch.  
• Do not install switch at the low point of a conduit run.  
• Install a fitting into the conduit opening that provides  
strain relief to the wires/cable, as well as sealing  
against contaminants found in the application.  
• In applications where fluids or moisture may be  
present, seal the fitting threads with a product such  
as Teflon tape or pipe dope.  
Failure to comply with these instructions could result in  
death or serious injury.  
REVERSING THE ROLLER LEVER  
The roller arm may be reversed to face the roller to the  
inside or outside of the arm.  
ADJUSTABLE LENGTH LEVERS  
1. Loosen the lever’s adjustment screw using a Phillips  
head screwdriver.  
2. Adjust to desired length.  
3. Securely tighten adjustment screw to  
GENERAL INFORMATION  
1. Refer to page 2 for specifications.  
2. Rotate switch head to desired position  
(90° increments). Review adjusting instructions  
below.  
1.0 N m [8.85 in lb] of torque.  
3. Mount switch using two M4 or #8 screws (not  
included). Torque screws to mounting surface  
4,9 N m to 5,9 N m [43.4 in lb to 52.2 in lb].  
4. All Normally Closed (NC) contacts are Direct  
TOP ROLLER PLUNGER  
Switches with top roller plunger must be mounted with  
plunger in desired position. Actuating device must not  
exceed over travel distance.  
Opening.  
WIRING  
ADJUSTMENT INSTRUCTIONS  
1. Remove front cover plate screw.  
2. Contact block area by terminal screw is labeled for  
NO (Normally Open) and NC (Normally Closed)  
contacts.  
To give flexibility in application, the user can perform the  
adjustments described below in any order before wiring  
the unit.  
3. Connect stranded wire (0,75 mmꢀ - 2,5 mmꢀ,  
18 AWG-14 AWG) or solid wire (0,75 mmꢀ - 1,5 mmꢀ,  
18 AWG-16 AWG) to desired connector terminals.  
Use 90 °C [194 °F] rated wire when ambient  
temperature is to exceed 75 °C [158 °F]:  
• Torque switch terminal screws to  
0,8 N m to 1,0 N m [7.1 in lb to 8.9 in lb]  
4. Securely tighten cover screw to 0,5 N m [4.4 in lb] of  
torque.  
ACTUATOR HEAD POSITIONING  
The actuator head may be positioned in any of four  
directions.  
1. Remove the four head retaining screws while  
holding actuator head in place.  
2. To prevent actuator spring loss, remove head slowly  
to relieve spring tension prior to removal.  
3. Rotate actuator head to desired position.  
4. Position the large diameter end of the actuator  
spring over the actuator. Place retaining screws  
through gasket material and position head over  
screw holes in desired position.  
5. Securely tighten the screws to 0,2 N m [1.7 in lb] of  
torque.  
Sensing and Control  
12345

中文翻译

下载PDF

与GLLA01A2B相关器件

型号 品牌 获取价格 描述 数据表
GLLA01A4J HONEYWELL

获取价格

 		Snap Acting/Limit Switch, SPDT, Momentary, 10A, 250VDC, Adjustable Rod Actuator, Panel Mou
GLLA03A4J HONEYWELL

获取价格

 		Snap Acting/Limit Switch, SPDT, Momentary, 10A, 250VDC, Adjustable Rod Actuator, Panel Mou
GLLA03D HONEYWELL

获取价格

 		Snap Acting/Limit Switch, SPDT, Momentary, 10A, 250VDC, Roller Lever Actuator, Panel Mount
GLLA04A4J HONEYWELL

获取价格

 		Snap Acting/Limit Switch, SPDT, Momentary, 10A, 250VDC, Adjustable Rod Actuator, Panel Mou
GLLA04B HONEYWELL

获取价格

 		Snap Acting/Limit Switch, SPDT, Momentary, 10A, 250VDC, Top Pin Plunger Actuator, Panel Mo
GLLA04C HONEYWELL

获取价格

 		Snap Acting/Limit Switch, SPDT, Momentary, 10A, 250VDC, Top Roller Plunger Actuator, Panel
GLLA04D HONEYWELL

获取价格

 		Snap Acting/Limit Switch, SPDT, Momentary, 10A, 250VDC, Roller Lever Actuator, Panel Mount
GLLA04F HONEYWELL

获取价格

 		Snap Acting/Limit Switch, SPDT, Momentary, 10A, 250VDC, Roller Lever Actuator, Panel Mount
GLLA06A1B HONEYWELL

获取价格

 		Snap Acting/Limit Switch, DPST, Momentary, 10A, 250VDC, Roller Type Actuator, Panel Mount,
GLLA06A4J HONEYWELL

获取价格

 		Snap Acting/Limit Switch, DPST, Momentary, 10A, 250VDC, Adjustable Rod Actuator, Panel Mou

与GLLA01A2B相关文章

您还可以找


热门产品
PCB打样/小批量
铝基板
BOM智能配单
PCBA制造
钣金
精密CNC
模具注塑
薄膜开关
精选活动
PCBA打样特惠
四六层板品质升级
铝基板品质升级
一体化电子制造
DFM下载
服务支持
企业认证
产品展示
工厂展示
工艺能力
积分商城
关于捷配
捷配简介
企业文化
公司动态
人才招聘
联系我们
帮助中心
下单流程
付款流程
开票流程
常见问题
全球PCB制造服务专线 400-613-0088

工作时间：9:00-21:00

CEO邮箱：ceo@jiepei.com

投诉邮箱：tousu@jiepei.com

捷配网-微信公众号 微信公众号
捷配网-微信公众号 抖音公众号
资质认证：
合作快递：
支付方式：
Copyright © 2024 Jiepei.com Inc. All Rights Reserved. 版权所有:杭州捷配信息科技有限公司 浙公网安备 33010502006866号 浙ICP备10014259号-119 营业执照ICP证