F97 Series
Resin-Molded Chip, Improved Reliability J-Lead
TECHNICAL SPECIFICATIONS
Item
Performance Characteristics
Category Temperature Range -55 to +125°C (Rated temperature: +85°C)
Capacitance Tolerance
Dissipation Factor
ESR (100kHz)
20%ꢀ 10% (at 120Hꢁ)
Refer to next page
Refer to next page
• After 1 minute’s application of rated voltageꢀ leakage current at 20°C
is not more than 0.01CV or 0.5μAꢀ whichever is greater.
• After 1 minute’s application of rated voltageꢀ leakage current at 85°C
is not more than 0.1CV or 5μAꢀ whichever is greater.
• After 1 minute’s application of derated voltageꢀ leakage current at 125°C
is not more than 0.125CV or 6.3μAꢀ whichever is greater.
+15% Max. (at +125°C)
LEAD-FREE COMPATIBLE
COMPONENT
Leakage Current
FEATURES
Capacitance Change
by Temperature
+10% Max. (at +85°C)
-10% Max. (at -55°C)
• Compliant to the RoHS2 directive 2011/65/EU
• Compliant to AEC-Q200
• Improved reliability - FR=0.5%/1000hrs (twice better than standard)
• SMD J-lead
At 85ºCꢀ 85% R.H.ꢀ For 1000 hours (No voltage applied)
Capacitance Change ........... Within 10% of the initial value
Dissipation Factor................ Initial specified value or less
Leakage Current.................. 125% or less than the initial specified value
After 1000 hour’s application of rated voltage in series with a 33Ω resistor
at 85˚Cꢀ 85% R.H.ꢀ capacitors meet the characteristics requirements
table below.
Capacitance Change ........... Within 10% of the initial value
Dissipation Factor................ 120% or less than the initial specified value
Leakage Current.................. 200% or less than the initial specified value
At -55°C / +125°Cꢀ For 30 minutes eachꢀ 1000 cycles
Capacitance Change ........... Within 5% of the initial value
Dissipation Factor................ Initial specified value or less
Leakage Current.................. Initial specified value or less
10 seconds reflow at 260°Cꢀ 5 seconds immersion at 260°C.
Capacitance Change ........... Within 5% of the initial value
Dissipation Factor................ Initial specified value or less
Leakage Current.................. Initial specified value or less
After immersing capacitors completely into a solder pot at 245ºC for 2 to 3
secondsꢀmore than 3/4 of their electrode area shall remain covered with
new solder.
After application of surge voltage in series with a 33Ω resistor at the rate of
30 seconds ONꢀ 30 seconds OFFꢀ for 1000 successive test cycles at 85ºCꢀ
capacitors shall meet the characteristic requirements table below.
Capacitance Change ........... Within 5% of the initial value
Dissipation Factor................ Initial specified value or less
Leakage Current.................. Initial specified value or less
After 2000 hours’ application of rated voltage in series with a 3Ω resistor at
85°Cꢀ or derated voltage in series with a 3Ω resistor at 125°Cꢀ capacitors
shall meet the characteristic requirements table below.
Capacitance Change ........... Within 10% of the initial value
Dissipation Factor................ Initial specified value or less
Leakage Current.................. Initial specified value or less
After applying the pressure load of 5N for 10
Damp Heat
(Steady State)
APPLICATIONS
• Automotive electronics(Engine ECU)
• Industrial equipment
Load Humidity
Temperature Cycles
CASE DIMENSIONS: millimeters (inches)
Code
L
W1
W2
H
S
Resistance to
Soldering Heat
3.20 0.20
1.60 0.20
1.20 0.10
1.60 0.20
0.80 0.20
A
(0.126 0.008ꢀ (0.063 0.008ꢀ (0.047 0.004ꢀ (0.063 0.008ꢀ (0.031 0.008ꢀ
3.50 0.20 2.80 0.20 2.20 0.10 1.90 0.20 0.80 0.20
(0.126 0.008ꢀ (0.110 0.008ꢀ (0.087 0.004ꢀ (0.075 0.008ꢀ (0.031 0.008ꢀ
6.00 0.20 3.20 0.20 2.20 0.10 2.50 0.20 1.30 0.20
(0.236 0.008ꢀ (0.126 0.008ꢀ (0.087 0.004ꢀ (0.098 0.008ꢀ (0.051 0.008ꢀ
7.30 0.20 4.30 0.20 2.40 0.10 2.80 0.20 1.30 0.20
(0.287 0.008ꢀ (0.169 0.008ꢀ (0.094 0.004ꢀ (0.110 0.008ꢀ (0.051 0.008ꢀ
Solderability
Surge
B
C
N
A, B CASE
C, N CASE
Endurance
Shear Test
L
W
1
L
W
1
H
H
1 seconds horiꢁontally to the center of
capacitor side body which has no electrode
and has been soldered beforehand on a
substrateꢀ there shall be found neither
17.7N (1.8kg
• f)
W2
W
2
For 60 seconds
S
S
S
S
exfoliation nor its sign at the terminal electrode.
Keeping a capacitor surface-mounted on a substrate upside down and
supporting the substrate at both of the opposite bottom points 45mm apart
MARKING
from the center of capacitorꢀ the pressure
20
strength is applied with a specified jig at the
center of the substrate so that substrate
may bend by1mm as illustrated. Thenꢀ there
shall be found no remarkable abnormality
on the capacitor terminals.
R230
Terminal Strength
Failure Rate
A CASE
B CASE
C CASE
N CASE
Capacitance
(μF)
Capacitance
(μF)
Capacitance
(μF)
Capacitance
Code
45
45
Month
Code
Month
Code
0.5% per 1000 hours at 85ºCꢀ VR with 0.1 /V series impedanceꢀ 60%
confidence level.
10
16r
Month
Code
C 475
Rated Voltage
(V)
Rated Voltage
(V)
Rated Voltage
(V)
Rated Voltage
Code
HOW TO ORDER
F97
1C
335
M
A
ٗ
Type
Rated
Voltage
Capacitance
Code
pF code: 1st two digits
represent significant figuresꢀ
3rd digit represents multiplier
(number of ꢁeros to follow)
Tolerance
K = 10%
M = 20%
Case
Size
See
table
above
Packaging
See page
168 for
details
JANUARY 2014 ■ 99
5秒后页面跳转
解析光耦仿真器：升级光耦合器技术的必要性
英伟达新一代Blackwell GPU过热问题致交付延迟
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
