SOLID TANTALUM ELECTROLYTIC CAPACITORS
Conformal coated
Chip
F95
Specifications
Item
Performance Characteristics
Category
Temperature Range
--55 ~ +125 (Rated temperature : 85
)
˚C ˚C
Capacitance Tolerance ± 20%, ± 10% (at 120Hz)
Dissipation Factor
Refer to P.220
(at 120Hz)
E.S.R.(100kHz) Refer to P.220
After 1 minute's application of rated voltage, leakage current at 20 is not
˚C
•
•
•
more than 0.01CV or 0.5 µA, whichever is greater.
After 1 minute's application of rated voltage, leakage current at 85 is not
˚C
Leakage Current
more than 0.1CV or 5 µA, whichever is greater.
After 1 minute's application of derated voltage, leakage current at 125 is
˚C
not more than 0.125CV or 6.3 µA, whichever is greater.
+15% Max. (at +125
)
˚C
Capacitance Change
by Temperature
+10% Max. (at +85
--10% Max. (at --55
)
˚C
)
˚C
At 40 , 90 ~ 95% R.H., For 500 hours (No voltage applied)
˚C
Capacitance Change • • • • • • Within ±10% of initial value
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • •• Initial specified value or less
At --55˚C / +125˚C, 30 minutes each, For 5 cycles,
Capacitance Change • • • • • • Within ± 5% of initial value
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • •• Initial specified value or less
Damp Heat
Type numbering system (Example : 35V 1.5 µF)
1
2
3
4
5
6
7
8
9
10 11
12 13 14
F 9 5 1 V 1 5 5 M A
A Q 2
Temperature Cycles
Single face electrode
Taping code
(Refer to page 211 for details)
Dipping Flow at 260 for 10 seconds, reflow at 260 for 10 seconds
˚C ˚C
Resistance to
Soldering Heat
Case code
Capacitance tolerance
Rated Capacitance
Capacitance Change • • • • • • Within ± 5% of initial value
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • •• Initial specified value or less
Rated voltage
Series
After application of surge voltage in series with a 33Ω resistor at the rate of 30
seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85
capacitors meet the characteristics requirements listed below.
Capacitance Change • • • • • • Within ±5% of initial value
,
˚C
Drawing
Surge
L
W
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • • • Initial specified value or less
After 2000 hours' application of rated voltage at 85 , or derated voltage at
˚C
125 , capacitors meet the characteristic requirements listed below.
˚C
H
Resin
Endurance
Capacitance Change • • • • • • Within ± 10% of initial value
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • ••• Initial specified value or less
After applying the pressure load of 5N
for 10± 1 seconds horizontally to the
center of capacitor side body which has
no electrode and has been soldered
beforehand on an aluminum substrate,
there shall be found neither exfoliation
nor its sign at the terminal electrode.
Solder
Solder
(D)
Shear Test
A
B
C
•
5N (0.51kg f)
For 10 ± 1 seconds
Single-side electrodes
(Both electrodes at bottom side only)
Keeping a capacitor surface-mounted on a substrate upside
down and supporting the substrate at both of the opposite
bottom points 45mm apart from the center of the capacitor,
the pressure strength is applied with
20
R230
a specified jig at the center of the
Terminal Strength
substrate so that the substrate may
bend by 1mm as illustrated. Then,
there shall be found no remarkable
Dimensions
(mm)
Case Code
L
W
H
A
B
C
(D)
45
45
P
S
A
B
(0.2)
(0.2)
(0.2)
(0.2)
2.2 ± 0.3 1.25 ± 0.3 1.0 ± 0.3 0.6 ± 0.3 0.8 ± 0.3 0.8 ± 0.3
3.2 ± 0.3 1.6 ± 0.3 1.0 ± 0.3 0.8 ± 0.3 1.2 ± 0.3 0.8 ± 0.3
3.2 ± 0.3 1.7 ± 0.3 1.3 ± 0.3 0.8 ± 0.3 1.2 ± 0.3 0.8 ± 0.3
3.3 ± 0.3 2.7 ± 0.3 1.7 ± 0.3 0.8 ± 0.3 1.2 ± 0.3 1.1 ± 0.3
abnormality on the capacitor terminals.
As for the surge and derated voltage at 125 , refer to page 210 for details.
˚C
D dimension only for reference
Standard ratings
4
6.3
10
16
1C
P
20
25
1E
S
35
1V
•
V
Cap.
Code
(µF)
0G
0J
1A
1D
1
105
155
225
335
475
685
106
156
226
336
476
686
107
157
227
S
A
1.5
2.2
3.3
4.7
6.8
P
S
S
A
A
•
S
A
•
(A) B
P
A
P
P
P
P
P
A
B
•
P
A
B
•
S
A
A
B
(B)
•
•
10
P
P
•
S
A
A
B
B
•
•
A
15
22
P
P
•
(P)
S
•
P
S
S
A
B
B
•
•
•
•
A
33
(P)
S
S
S
A
A
A
B
S
•
•
•
•
B
47
S
S
A
A
A
B
(A)
68
B
100
150
220
B
(
) The series in parentheses are being developed.
B
(B)
Please contact to your local Nichicon sales office when
these series are being designed in your application.
(B)
CAT.8100R
5秒后页面跳转
解析光耦仿真器：升级光耦合器技术的必要性
英伟达新一代Blackwell GPU过热问题致交付延迟
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
