SOLID TANTALUM ELECTROLYTIC CAPACITORS
Resin-molded Chip,
Standard Series
F93
Specifications
Compliant to the RoHS directive (2002/95/EC).
Item
Performance Characteristics
Category
Temperature Range
˚C
˚C
)
--55 to +125 (Rated temperature : +85
Capacitance Tolerance
± 20%, ±10% (at 120Hz)
Refer to next page
Dissipation Factor (120Hz) Refer to next page
ESR (100kHz)
After 1 minute's application of rated voltage, leakage current
•
•
•
at 20 is not more than 0.01CV or 0.5µA, whichever is greater.
˚C
After 1 minute's application of rated voltage, leakage current
Leakage Current
at 85 is not more than 0.1CV or 5µA, whichever is greater.
˚C
After 1 minute's application of derated voltage, leakage current
at 125 is not more than 0.125CV or 6.3µA, whichever is greater.
˚C
+15% Max. (at +125
)
˚C
)
)
Capacitance Change
by Temperature
+10% Max. (at +85
˚C
--10% Max. (at --55
˚C
˚C
At 40 90 to 95% R.H. 500 hours (No voltage applied)
...
........
Damp Heat
(Steady State)
Capacitance Change Refer to next page (* 1)
Dissipation Factor
Initial specified value or less
Initial specified value or less
Type numbering system (Example: 10V 10µF)
..........
Leakage Current
55 / +125 30 minutes each 5 cycles
˚C ˚C
--
1
2
3
4
5
6
7
8
9
10 11
...
Capacitance Change Refer to next page (* 1)
........
Taping code
F 9 3 1 A 1 0 6 M A
Temperature Cycles
(Refer to page 321 for details)
Dissipation Factor
Initial specified value or less
Initial specified value or less
..........
Leakage Current
Case code
Capacitance tolerance
Rated capacitance
Test condition:
10 seconds reflow at 260˚C , 5 seconds immersion at 260
˚C
Rated voltage
Series
Resistance
...
Capacitance Change Refer to next page (* 1)
........
Dissipation Factor
Leakage Current
to Soldering Heat
Initial specified value or less
Initial specified value or less
Drawing
..........
•
•
A
B Case
C
N Case
After application of surge voltage in series with a 33Ω resistor at the rate of
30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at
85 ,capacitors meet the characteristics requirements listed below.
˚C
Surge
.....
Capacitance Change
.........
Refer to next page (* 1)
Initial specified value or less
Initial specified value or less
Dissipation Factor
...........
Leakage Current
After 2000 hours' application of rated voltage in series with a 3
Ω resistor
at 85 , or derated voltage in series with a 3 resistor at 125
Ω
,
˚C
˚C
capacitors meet the characteristic requirements listed below.
Endurance
......
Capacitance Change
Refer to next page (* 1)
Initial specified value or less
Initial specified value or less
..........
Dissipation Factor
............
Leakage Current
After applying the pressure load of 5N for 10±1 seconds
horizontally to the center of capacitor side body which has no
electrode and has been soldered
beforehand on an aluminum substrate,
there shall be found neither exfoliation nor
its sign at the terminal electrode.
Dimensions
(mm)
S
Case code
L
W1
W2
H
Shear Test
A
B
C
N
3.2 ± 0.2 1.6 ± 0.2 1.2 ± 0.1 1.6 ± 0.2 0.8 ± 0.2
3.5 ± 0.2 2.8 ± 0.2 2.2 ± 0.1 1.9 ± 0.2 0.8 ± 0.2
6.0 ± 0.2 3.2 ± 0.2 2.2 ± 0.1 2.5 ± 0.2 1.3 ± 0.2
7.3 ± 0.2 4.3 ± 0.2 2.4 ± 0.1 2.8 ± 0.2 1.3 ± 0.2
Keeping a capacitor surface-mounted on a substrate upside down
and supporting the substrate at both of the opposite bottom points
45mm apart from the center of the
capacitor, the pressure strength is
Marking
applied with a specified jig at the
Terminal Strength
A Case
C685
B Case
C Case
N Case
center of the substrate so that the
substrate may bend by 1mm as
22
16V
illustrated. Then, there shall be found
no remarkable abnormality on the
capacitor terminals.
As for the surge and derated voltage at 125 , refer to page 320 for details.
˚C
Capacitance (µF) Rated voltage (V)
(Rated voltage code) (Capacitance code) Rated voltage (V)
2.5V
4V
e
G
J
20V
D
E
V
25V
35V
6.3V
10V
16V
A
C
Standard Ratings
V
4
0G
6.3
0J
10
1A
16
1C
20
1D
25
1E
35
1V
Code
Cap. (µF)
0.68
1
684
105
155
225
335
475
685
106
156
226
336
476
686
107
157
227
337
477
687
A
A
A
•
A
A
A
A
•
1.5
2.2
3.3
4.7
6.8
10
15
22
33
47
68
100
150
220
330
470
680
A
A
A
A
•
A
A
•
A
B
B
•
A
A
A
B
B
B
A
B
C
N
B
C
•
•
A
A
A
A
•
C
C
N
N
•
A
A
A
A
•
A
A
•
B
B
•
B
C
•
C
•
C
•
A
A
A
A
•
A
B
•
C
B
C
C
C
N
N
•
A
B
B
C
•
N
N
•
•
•
•
A
A
•
B
B
•
A
B
B
•
C
N
(B)
C
N
•
N
•
B
•
C
•
(N)
A
B
A
B
B
•
C
N
C
•
C
N
B
B
C
N
N
B
•
C
•
C
N
N
N
•
•
(A)
C
C
N
N
N
N
( ) The series in parentheses are being developed.
Please contact to your local Nichicon sales office when these
series are being designed in your application.
CAT.8100Z
5秒后页面跳转
解析光耦仿真器：升级光耦合器技术的必要性
英伟达新一代Blackwell GPU过热问题致交付延迟
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
