SOLID TANTALUM ELECTROLYTIC CAPACITORS
Resin-molded Chip,
Standard Series
F93
Specifications
Compliant to the RoHS directive (2002/95/EC).
Item
Performance Characteristics
Category
Temperature Range
˚C
˚C
)
--55 to +125 (Rated temperature : +85
Capacitance Tolerance
±20%, ±10% (at 120Hz)
Dissipation Factor (120Hz) Refer to next page
ESR (100kHz)
Refer to next page
After 1 minute's application of rated voltage, leakage current
at 20 is not more than 0.01CV or 0.5µA, whichever is greater.
˚C
After 1 minute's application of rated voltage, leakage current
at 85 is not more than 0.1CV or 5µA, whichever is greater.
˚C
After 1 minute's application of derated voltage, leakage current
at 125 is not more than 0.125CV or 6.3µA, whichever is greater.
˚C
•
•
•
Leakage Current
+15% Max. (at +125
)
˚C
)
)
Capacitance Change
by Temperature
+10% Max. (at +85
˚C
--10% Max. (at --55
˚C
˚C
At 40 90 to 95% R.H. 500 hours (No voltage applied)
...
........
Damp Heat
(Steady State)
Capacitance Change Refer to next page (* 1)
Dissipation Factor
Initial specified value or less
Initial specified value or less
Type numbering system (Example: 10V 10µF)
..........
Leakage Current
55 / +125 30 minutes each 5 cycles
˚C ˚C
--
...
........
Capacitance Change Refer to next page (* 1)
Temperature Cycles
Dissipation Factor
Initial specified value or less
Initial specified value or less
..........
Leakage Current
Test condition:
10 seconds reflow at 260˚C , 5 seconds immersion at 260
...
˚C
Resistance
Capacitance Change Refer to next page (* 1)
to Soldering Heat
........
Dissipation Factor
Initial specified value or less
Initial specified value or less
Drawing
..........
Leakage Current
•
•
N Case
A
B Case
C
After application of surge voltage in series with a 33Ω resistor at the rate of
30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at
85 ,capacitors meet the characteristics requirements listed below.
˚C
Surge
.....
Capacitance Change
.........
Refer to next page (* 1)
Initial specified value or less
Initial specified value or less
Dissipation Factor
...........
Leakage Current
After 2000 hours' application of rated voltage in series with a 3
Ω resistor
at 85 , or derated voltage in series with a 3 resistor at 125
Ω
,
˚C
˚C
capacitors meet the characteristic requirements listed below.
Endurance
......
Capacitance Change
Refer to next page (* 1)
Initial specified value or less
Initial specified value or less
..........
Dissipation Factor
............
Leakage Current
After applying the pressure load of 5N for 10±1 seconds
horizontally to the center of capacitor side body which has no
electrode and has been soldered
beforehand on an aluminum substrate,
there shall be found neither exfoliation nor
its sign at the terminal electrode.
Dimensions
(mm)
Case code
L
W1
W2
H
S
Shear Test
A
B
C
N
3.2 ± 0.2 1.6 ± 0.2 1.2 ± 0.1 1.6 ± 0.2 0.8 ± 0.2
3.5 ± 0.2 2.8 ± 0.2 2.2 ± 0.1 1.9 ± 0.2 0.8 ± 0.2
6.0 ± 0.2 3.2 ± 0.2 2.2 ± 0.1 2.5 ± 0.2 1.3 ± 0.2
7.3 ± 0.2 4.3 ± 0.2 2.4 ± 0.1 2.8 ± 0.2 1.3 ± 0.2
Keeping a capacitor surface-mounted on a substrate upside down
and supporting the substrate at both of the opposite bottom points
45mm apart from the center of the
capacitor, the pressure strength is
Marking
applied with a specified jig at the
Terminal Strength
A Case
C685
B Case
C Case
N Case
center of the substrate so that the
substrate may bend by 1mm as
22
16V
illustrated. Then, there shall be found
no remarkable abnormality on the
capacitor terminals.
As for the surge and derated voltage at 125 , refer to page 308 for details.
˚C
Capacitance (µF) Rated voltage (V)
(Rated voltage code) (Capacitance code) Rated voltage (V)
2.5V
4V
e
G
J
20V
D
E
V
25V
35V
6.3V
10V
16V
A
C
Standard Ratings
V
4
0G
6.3
0J
10
1A
16
1C
20
1D
25
1E
35
1V
A
Code
Cap. (
µF)
0.47
0.68
1
1.5
2.2
3.3
4.7
6.8
10
15
22
33
47
474
684
105
155
225
335
475
685
106
156
226
336
476
686
107
157
227
337
477
687
A
A
A
A
A
•
A
A
A
•
A
A
A
A
A
•
A
A
•
A
B
B
•
A
A
A
A
A
A
A
A
•
A
A
A
B
B
B
A
B
C
N
B
C
•
•
C
C
N
N
•
A
A
•
B
B
•
B
C
•
A
A
A
•
B
B
B
•
C
•
C
•
•
•
A
A
B
•
C
B
C
C
C
N
N
•
•
A
A
A
•
A
•
B
C
•
N
N
•
A
A
•
B
B
•
A
B
B
•
C
N
(B)
C
N
•
N
•
68
B
•
C
•
(N)
100
150
220
330
470
680
A
B
A
B
B
•
C
N
C
•
C
N
B
B
C
N
N
B
•
C
•
C
N
N
N
•
•
(A)
C
C
N
N
N
N
( ) The series in parentheses are being developed.
Please contact to your local Nichicon sales office when these
series are being designed in your application.
CAT.8100Y-1