F72/F75 Series
Low Profile and High CV Conformal Coated Chip
RATINGS & PART NUMBER REFERENCE
100kHz RMS Current (mA)
Rated
Voltage
(V)
DF
ESR
*1
ΔC/C
(%)
AVX
Case
Capacitance
(μF)
DCL
(μA)
@ 120Hz @ 100kHz
MSL
Part No.
Size
25ºC
85ºC
125ºC
(%)
(Ω)
F750J477#UC
F750J687#DC
F750J687#RC
F750J108#RC
F750J108#UCAQ2
F750J228#MCAQ2
U
D
R
R
U
M
470
680
680
1000
1000
2200
6.3
6.3
6.3
6.3
6.3
6.3
29.6
42.8
42.8
63.0
126
15
18
18
24
40
60
0.10
0.12
0.12
0.12
0.15
0.08
1049
1118
1443
1443
856
944
1006
1299
1299
771
420
447
577
577
343
632
*
*
*
*
±20
±20
3
3
3
3
3
3
139
1581
1423
10 Volt
16 Volt
F751A157#CC
F751A227#CC
F751A227#DC
F751A337#DC
F751A477#RC
F751A477#UCAQ2
C
C
D
D
R
U
150
220
220
330
470
470
10
10
10
10
10
10
15.0
22.0
22.0
33.0
47.0
94.0
10
10
10
10
14
30
0.22
0.20
0.20
0.15
0.12
0.15
707
742
866
1000
1443
856
636
667
779
900
1299
771
283
297
346
400
577
343
*
*
*
*
*
3
3
3
3
3
3
±20
F751C686#CC
F751C107#CC
F751C157#DC
F751C227#RC
C
C
D
R
68
16
16
16
16
10.9
16.0
24.0
35.2
10
10
10
10
0.22
0.22
0.22
0.20
707
707
826
636
636
743
283
283
330
447
*
*
*
*
3
3
3
3
100
150
220
1118
1006
#: "M" for ±20% tolerance, "K" for ± 10% tolerance.
Moisture Sensitivity Level (MSL) is defined according to J-STD-020.
*1: ΔC/C Marked “*”
Item
F72/F75 All Case (%)
Damp Heat
Temperature cycles
±10
±5
Resistance soldering heat
Surge
±5
±5
Endurance
±10
QUALIFICATION TABLE
F72/75 series (Temperature range -55ºC to +125ºC)
Condition
TEST
At 40°C, 90 to 95% R.H., 500 hours (No voltage applied)
Capacitance Change .................. Refer to the table above (*1)
Dissipation Factor ....................... Initial specified value or less
Leakage Current .......................... Initial specified value or less
Damp Heat
(Steady State)
At -55°C / +125°C, 30 minutes each, 5 cycles
Capacitance Change .................. Refer to the table above (*1)
Dissipation Factor ....................... Initial specified value or less
Leakage Current .......................... Initial specified value or less
Temperature Cycles
10 seconds reflow at 260°C, 10 seconds immersion at 260°C.
Capacitance Change .................. Refer to the table above (*1)
Dissipation Factor ....................... Initial specified value or less
Leakage Current .......................... Initial specified value or less
Resistance to
Soldering Heat
After application of surge voltage in series with a 33Ω resistor at the rate of 30 seconds ON, 30 seconds OFF,
for 1000 successive test cycles at 85ºC, capacitors shall meet the characteristic requirements in the table above.
Capacitance Change .................. Refer to the table above (*1)
Surge
Dissipation Factor ....................... Initial specified value or less
Leakage Current .......................... Initial specified value or less
After 2000 hours’ application of rated voltage at 85°C,
capacitors shall meet the characteristic requirements in the table above.
Capacitance Change .................... Refer to the table above (*1)
Dissipation Factor ......................... Initial specified value or less
Leakage Current ........................... Initial specified value or less
Endurance
After applying the pressure load of 5N for 10±1 seconds horizontally to the center of capacitor side body which
has no electrode and has been soldered beforehand on a substrate, there shall be found neither exfoliation nor
its sign at the terminal electrode.
Shear Test
Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the
opposite bottom points 45mm apart from the center of capacitor, the pressure strength is applied with a specified
jig at the center of substrate so that the substrate may bend by 1mm as illustrated. Then, there shall
be found no remarkable abnormality on the capacitor terminals.
Terminal Strength
The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or
available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order.
162
042920