SOLID TANTALUM ELECTROLYTIC CAPACITORS
LOW ESR
Resin-molded Chip
F91
Compliant to the RoHS directive (2002/95/EC).
Specifications
Item
Performance Characteristics
Category
Temperature Range
˚C
˚C
)
+
--55 to +125 (Rated temperature : 85
Capacitance Tolerance
Dissipation Factor (120Hz)
ESR (100kHz)
±20%, ±10% (at 120Hz)
Refer to the table below.
Refer to the table below.
After 1 minute's application of rated voltage, leakage current
•
•
•
at 20 is not more than 0.01CV or 0.5µA, whichever is greater.
˚C
After 1 minute's application of rated voltage, leakage current
Leakage Current
at 85 is not more than 0.1CV or 5µA, whichever is greater.
˚C
After 1 minute's application of derated voltage, leakage current
at 125 is not more than 0.125CV or 6.3µA, whichever is greater.
˚C
+15% Max. (.at +125
)
˚C
)
)
Capacitance Change
by Temperature
+10% Max. (at +85
˚C
--10% Max. (at --55
˚C
At 40˚C 90 to 95% R.H. 500 hours (No voltage applied)
Capacitance Change Within ±10% of the initial value
......
Type numbering system (Example : 10V 100µF)
Damp Heat
(Steady State)
Dissipation Factor
Initial specified value or less
Initial specified value or less
........
10 11
1
2
3
4
5
6
7
8
9
Leakage Current
Taping code
(Refer to page 333 for details)
--55˚C / +125˚C 30 minutes each 5 cycles
C
F 9 1 1 A 1 0 7 M
Capacitance Change Within ±5% of the initial value
Temperature Cycles
Case code
Capacitance tolerance
Rated capacitance
......
........
Dissipation Factor
Leakage Current
Initial specified value or less
Initial specified value or less
Rated voltage
Series
˚C,
10 seconds reflow at 260
˚C
5 seconds immersion at 260
Resistance
Capacitance Change Within ±5% of the initial value
to Soldering Heat
......
........
Dissipation Factor
Leakage Current
Initial specified value or less
Initial specified value or less
Drawing
•
C N Case
After application of surge in series with a 33Ω resistor at the rate of 30
seconds ON, 30 seconds OFF, for 1000 sucessive test cycles at 85
,
˚C
capacitors shall meet the characteristic requirements table below.
....
Capacitance Change Within ±5% of the initial value
L
W1
Surge
........
..........
Dissipation Factor
Leakage Current
Initial specified value or less
Initial specified value or less
H
After 2000 hours' application of rated voltage in series with a 3
Ω resistor
at 85˚C, or derated voltage in series with a 3 resistor at 125˚C
Ω
,
capacitors shall meet the characteristics requirements table below.
Capacitance Change......Within ±10% of the initial value
Dissipation Factor..........Initial specified value or less
Leakage Current............Initial specified value or less
W2
Endurance
S
S
After applying the pressure load of 5N for 10±1 seconds
horizontally to the center of capacitor side body which has no
electrode and has been soldered
beforehand on a substrate, there shall
be found neither exfoliation nor its sign
at the terminal electrode.
Dimensions
(
mm)
Shear Test
Case Code
L
W2
3.2 ± 0.2 2.2 ± 0.1
H
W1
S
C
N
6.0 ± 0.2
7.3 ± 0.2
2.5 ± 0.2
2.8 ± 0.2
1.3 ± 0.2
1.3 ± 0.2
4.3 ± 0.2
2.4 ± 0.1
Keeping a capacitor surface-
mounted on a substrate upside down
and supporting the substrate at both
of the opposite bottom points 45mm
apart from the center of capacitor,
the pressure strength is applied with
a specified jig at the center of
Marking
Terminal Strength
C Case
N Case
substrate so that the substrate may bend by 1mm as illustrated.
Then, there shall be found no remarkable abnormality on the
capacitor terminals.
As for the surge and derated voltage at 125 , refer to page 332 for details.
˚C
Rated voltage (V)
Rated voltage (V)
Rated Capacitance (µF)
Rated
Capacitance
(µF)
Leakage
Current
( A)
µ
Disspation
Factor
(%@120Hz)
Case
code
ESR
@100kHz)
Rated Volt
Part Number
(mΩ
Standard Ratings
F910G157MCC
F910G227MCC
F910G337MNC
F910G477MNC
F910G687MNC
F910J107MCC
F910J157MCC
F910J227MCC
F910J227MNC
F910J337MNC
F910J477MNC
F911A686MCC
F911A107MCC
F911A157MNC
F911A227MNC
F911A337MNC
150
220
330
470
680
100
150
220
220
330
470
68
C
C
N
N
N
C
C
C
N
N
N
C
C
N
N
N
6.0
8.8
12
12
10
16
18
8
250
250
100
100
100
250
250
250
100
100
100
300
250
100
100
100
V
4
6.3
10
1A
C
Cap.
F)
Code
13.2
18.8
27.2
6.3
0G
0J
4V
(
µ
068
100
150
220
330
470
680
686
107
157
227
337
477
687
C
C
C
N
N
N
C
C
N
N
N
9.5
12
14
10
14
16
8
C • N
N
13.9
13.9
20.8
29.6
6.8
6.3V
10V
N
100
150
220
330
10.0
15.0
22.0
33.0
10
10
12
18
In case of capacitance tolerance 10% type, K will be put at 9th digit of type numbering
±
system.
CAT.8100B