CONDUCTIVE POLYMER TANTALUM SOLID ELECTROLYTIC CAPACITORS
Conductive Polymer Resin-molded Chip,
Compact Series
F3 1
Adapted to the RoHS directive (2002/95/EC).
Specifications
Item
Performance Characteristics
Category Temperature Range –55 to +105˚C (Rated temperature + 85˚C)
Capacitance Tolerance ±20% (120Hz)
Dissipation Factor(at 120Hz) Refer to the list below
ESR (100kHz)
Leakage Current
Ripple Current
Refer to the list below
After 5 minutes' application of rated voltage, leakage current
at 20˚C is not more than 0.1CV
Refer to the list below
At 60˚C, 90 to 95% R.H. 500hours
..
.......
.........
Damp Heat
(No voltage applied)
Capacitance Change Within –20 to +30% of initial value
Dissipation Factor
1.5 times Initial specified value or less
Initial specified value or less
Type numbering system (Example : 6.3V 47 µF)
Leakage Current
–55˚C / +105˚C 30 minutes each 5 cycle
..
1
2
3
4
5
6
7
8
9
10 11
Capacitance Change Within ±20% of initial value
Taping code
F 3 1 0 J 4 7 6 M B A
Temperature Cycles
.......
.........
Dissipation Factor
Leakage Current
Initial specified value or less
Initial specified value or less
(Refer to page 300 for details)
Tape width Reel Dia Reel Dia
(mm)
(φ180mm) (φ330mm)
Test Condition;10 second reflow at 240˚C
A
8
E
..
Resistance
to Soldering Heat
Capacitance Change Within ±20% of initial value
.......
.........
Case code
Dissipation Factor
Leakage Current
1.3 times Initial specified value or less
Initial specified value or less
Capacitance tolerance
Rated Capacitance
Rated voltage
Series
After application of surge voltage in series with a 1kΩ resistor
at the rate of 30 seconds ON, 30 seconds OFF, for 1000
successive test cycles at 85˚C, capacitors meet the
characteristics requirements listed below.
Surge
...
Capacitance Change Within ±20% of initial value
........
..........
Dissipation Factor
Leakage Current
Initial specified value or less
Initial specified value or less
Dimensions
After 1000 hours' application of rated voltage in series
L
W1
with a 3Ω resistor at 85˚C.
....
Endurance
Endurance
1
2
Capacitance Change Within ±20% of initial value
H
...
Dissipation Factor 1.5 times Initial specified value or less
...
Leakage Current Initial specified value or less
After 1000 hours' application of rated voltage in series
with a 3Ω resistor at 105˚C,capacitors meet the characteristic
requirements listed below
W2
S
S
....
Capacitance Change Within ±20% of initial value
(mm)
...
Dissipation Factor 3 times Initial specified value or less
Case code
W2
H
W1
S
L
...
Leakage Current Initial specified value or less
2.0±0.2
1.1±0.1
1.1±0.1
1.1±0.1
0.5±0.2
0.8±0.2
0.8±0.2
P
A
B
1.25±0.1
1.6±0.2
2.8±0.2
0.9±0.1
1.2±0.1
2.3±0.1
After applying the pressure load of 5N for 10±1 seconds
horizontally to the center of capacitor side body which has
no electrode and has been soldered beforehand on an
aluminum substrate, neither exfoliation
3.2±0.2
3.4±0.2
Shear Test
not its sign shall be found at the terminal
electrode.
•
5N (0.51kg f)
For 10±1seconds
Keeping a capacitor surface-mounted on a substrate upside
down and supporting the substrate at both of the opposite
bottom points 45mm apart from the center of the capacitor,
the pressure load is applied with a specified jig at the center
of the substrate so that the substrate may bend by 1mm as
Marking
P Case
A Case
B Case
Conductive
Polymer
Rated Capacitance (µF)
Capacitance
Terminal Strength
code
illustrated.
20
33
P6v
Ja
Jar
Rated
Voltage
code
R230
Then, there shall be found no
remarkable abnormality on the
capacitor terminals.
Capacitance
code
Month code
Month
code
Rated
Conductive Polymer
Voltage
code
45
45
"
"
)
Rated Voltage (6.3V is marked as 6V
As for the surge voltage refer to page 299 for details.
CAT.8100W-2
5秒后页面跳转
解析光耦仿真器：升级光耦合器技术的必要性
英伟达新一代Blackwell GPU过热问题致交付延迟
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
