5秒后页面跳转
EY3A-110-A PDF预览

EY3A-110-A

更新时间: 2024-11-24 10:17:39
品牌 Logo 应用领域
欧姆龙 - OMRON 传感器
页数 文件大小 规格书
2页 47K
描述
Single Beam Sensor (1 Beam: 100 mm)

EY3A-110-A 数据手册

 浏览型号EY3A-110-A的Datasheet PDF文件第2页 
Single Beam Sensor (1 Beam: 100 mm)  
EY3A-110-A  
Dimensions  
Note: All units are in millimeters unless otherwise indicated.  
Features  
Ensures higher sensitivity and external light interference resistivity  
than any other photomicrosensor.  
Narrow sensing range ensures stable sensing of a variety of sens-  
ing objects.  
Center of  
positioning boss  
Center of detector  
2-R2  
41.6 0.1  
2.7 0.1  
Absolute Maximum Ratings (Ta = 25°C)  
Item  
Symbol  
VCC  
VOUT  
IOUT  
Rated value  
8.3 dia  
3.05  
.
Power supply voltage  
7 V  
7 V  
5 dia.  
Load voltage  
Load current  
dia.  
10  
dia.  
10 mA  
Center of emitter  
Pin No. 1  
4
Ambient  
temperature  
Operating  
Storage  
Topr  
Tstg  
0°C to 60° C  
–15°C to 70° C  
3.6  
Note: Make sure there is no icing or condensation when operating the  
Sensor.  
30 0.1  
17  
1
C
58  
64.4  
Ordering Information  
0
3.20.2 dia.  
Description  
Single beam sensor  
Model  
EY3A-110-A  
Pin no. Remarks  
Name  
1
2
3
O
V
Output (OUT)  
Power supply (Vcc)  
Ground (GND)  
G
Unless otherwise specified, the  
tolerances are as shown below.  
Dimensions  
3 mm max.  
Tolerance  
0.3  
3 < mm 6  
0.375  
0.45  
6 < mm 10  
10 < mm 18  
18 < mm 30  
30 < mm 50  
50 < mm 80  
0.55  
0.65  
Recommended Mating Connectors:  
Tyco Electronics AMP 173977-3 (press-fit connector)  
179228-3 (crimp connector)  
0.8  
0.95  
175778-3 (crimp connector)  
Electrical and Optical Characteristics (Ta = 0°C to 60°C)  
Item  
Power supply voltage  
Value  
Condition  
5 V 5%  
---  
Current consumption  
50 mA max.  
VCC = 5 V, RL = ∞  
VCC = 5 V, RL = ∞  
Peak current consumption  
Low-level output voltage  
High-level output voltage  
Response delay time (high to low)  
200 mA max.  
0.6 V max.  
3.5 V min.  
VCC = 5 V, IOL = 4 mA (see note 1)  
VCC = 5 V, RL = 4.7 k(see note 2)  
1.5 ms max.  
The time required for the output to become “Lo” after placing  
sensing object.  
Response delay time (low to high)  
1.5 ms max.  
The time required for the output to become “Hi” after removing  
sensing object.  
Note: 1. These conditions are for the sensing of lusterless paper with an OD of 0.9 maximum located at the correct sensing position of the Sensor  
as shown in the optical path arrangement on the next page.  
2. These conditions are for the sensing of the paper supporting plate with an OD of 0.05 located using the glass plate without paper as  
shown in the optical path arrangement on the next page.  
134  
Single Beam Sensor (1 Beam: 100 mm) EY3A-110-A  

与EY3A-110-A相关器件

型号 品牌 获取价格 描述 数据表
EY3A-112 OMRON

获取价格

Single Beam Sensor (1 Beam: 125 mm)
EY3A-3051 OMRON

获取价格

Through Beam Photoelectric Sensor, 50mm Max, 0.60-3.50V, Rectangular
EY3A-308 OMRON

获取价格

Through Beam Photoelectric Sensor, 80mm Min, 80mm Max, 0.60-3.50V, Rectangular
EY470KE OHMITE

获取价格

Fixed Resistor
EY471KE OHMITE

获取价格

RES 470 OHM 2.5W 10% AXIAL
EY472KE OHMITE

获取价格

RES 4.7K OHM 2.5W 10% AXIAL
EY473KE OHMITE

获取价格

Fixed Resistor
EY680KE OHMITE

获取价格

RES 68 OHM 2.5W 10% AXIAL
EY681KE OHMITE

获取价格

RES 680 OHM 2.5W 10% AXIAL
EY80 ETC

获取价格

VEB WERK FUR FERNMELDEWESEN