LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS
Long life snap-ins, 105℃
LXG
LXGSeries
Longer life
KMQ P215
Endurance with ripple current : 5,000 hours at 105
Non solvent resistant type
RoHS Compliant
・
・
・
℃
SPECIFICATIONS
◆
Items
Characteristics
Category
Temperature Range
-
40 to +105℃
(at 20℃, 120Hz)
Rated Voltage Range 10 to 100Vdc
Capacitance Tolerance ±20% (M)
Leakage Current
I=0.02CV or 3mA, whichever is smaller.
Where, I : Max. leakage current ( A), C : Nominal capacitance (
10V 16V 25V 35V 50V 63V 80 & 100V
0.60 0.45 0.30 0.25 0.20 0.15 0.15
(at 20℃ after 5 minutes)
(at 20℃, 120Hz)
µ
µF), V : Rated voltage (V)
Dissipation Factor
(tanδ)
Rated voltage (Vdc)
tanδ(Max.)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Capacitance change : Capacitance at the lowest operating temperature shall not be less than 70% of the 20℃ value.
Rated voltage (Vdc)
10V 16V 25V 35V 50V 63V 80 & 100V
Z(-
25℃)/Z(+20℃)
40℃)/Z(+20℃)
4
4
3
3
8
2
6
2
6
2
5
(at 120Hz)
Z(
-
15
15
10
Endurance
Shelf Life
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjected to DC voltage with rated ripple
current is applied (the peak voltage shall not exceed the rated voltage) for 5,000 hours at 105℃.
Capacitance change
D.F. (tanδ)
≦±25% of the initial value
250% of the initial specified value
The initial specified value
≦
Leakage current
≦
The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 500 hours at 105℃ without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change
D.F. (tanδ)
≦±20% of the initial value
150% of the initial specified value
The initial specified value
≦
Leakage current
≦
DIMENSIONS [mm]
◆
●
●
Terminal Code : VS (φ22 toφ35) : Standard
Terminal Code : LI (φ35)
PC board pin-out
-1.2×6
Sleeve (PET : Brown)
Sleeve (PET : Brown)
Negative mark
Negative mark
PC board pin-out
2
5±0.5
2-φ2
*
14.2±1
4.0±0.5
L±2
L±2
4.5±1
Vent
Vent
*φD=35mm : 3.5±0.5mm
The standard design has no plastic disc.
PART NUMBERING SYSTEM
◆
1
2
3
4
5
6
7
8
9
10
11 12 13
14
15 16 17
18
E L X G A A A V S N A A A M A A A S
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 390µF:391, 3,300µF:332)
Dummy terminal code
Terminal code (VS, LI)
Voltage code (ex. 10V:100, 100V:101)
Series code
Category
Please refer to "Product code guide (snap-in type)"
RATED RIPPLE CURRENT MULTIPLIERS
◆
●Frequency Multipliers
Frequency (Hz)
10 to 50Vdc
63 to 100Vdc
50
0.95
0.92
120
1.00
1.00
300
1.03
1.07
1k
1.05
1.13
10k
1.08
1.19
50k
1.08
1.20
The endurance of capacitors is reduced with internal heating produced by ripple current at the rate of halving the lifetime with every 5 rise.
℃
When long life performance is required in actual use, the rms ripple current has to be reduced.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
CAT. No. E1001N
252