LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS
Downsized snap-ins, 105℃
KMRSeries
Rated voltage range : 160 to 450Vdc, Capacitance range : 100 to 3,300μF
For inverter control, switching power supplies
Non solvent resistant type
KMR
Downsized 5mm in height from current snap-ins KMQ series
Max. 50% up ripple current than same case size of KMQ series
・
・
・
・
・
・
・
Downsized
KMQ P215
Endurance with ripple current : 2,000 hours at 105
℃
RoHS Compliant
SPECIFICATIONS
◆
Items
Characteristics
Category
Temperature Range
-
25 to +105℃
Rated Voltage Range 160 to 450Vdc
Capacitance Tolerance
Leakage Current
±
20% (M)
I≦3 CV
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
(at 20℃, 120Hz)
(at 20℃ after 5 minutes)
(at 20℃, 120Hz)
Dissipation Factor
(tanδ)
Rated voltage (Vdc)
160 to 250V 315 to 400V 420 & 450V
0.15 0.15 0.20
160 to 250V 315 to 400V 420 & 450V
tanδ(Max.)
Rated voltage (Vdc)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Z(
-25℃)/Z(+20℃)
4
8
8
(at 120Hz)
Endurance
Shelf Life
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjected to DC voltage with the rated
ripple current is applied (the peak voltage shall not exceed the rated voltage) for 2,000 hours at 105℃.
Capacitance change
D.F. (tanδ)
Leakage current
≦±20% of the initial value
≦200% of the initial specified value
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃after exposing them for 1,000 hours at 105℃ without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change
D.F. (tanδ)
Leakage current
≦±15% of the initial value
≦150% of the initial specified value
≦The initial specified value
DIMENSIONS [mm]
◆
●
●
Terminal Code : VS (φ22 toφ35) : Standard
Terminal Code : LI (φ35)
Sleeve (PET : Brown)
PC board pin-out
Sleeve (PET : Brown)
PC board pin-out
-1.2×6
Negative mark
Negative mark
2
5±0.5
2-
φ2
14.2
±1
4.0±0.5
L±2.5
L
±
2.5
4.5±1
Vent
Vent
The standard design has no plastic disc.
PART NUMBERING SYSTEM
◆
1
2
3
4
5
6
7
8
9
10
11 12 13
14
15 16 17
18
E K M R
V S N
M
S
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 100µF:101, 2,700µF:272)
Dummy terminal code
Terminal code (VS, LI)
Voltage code (ex. 160V:161, 315V:3B1, 450V:451)
Series code
Category
Please refer to "Product code guide (snap-in type)"
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
CAT. No. E1001N
212