Plastic Film Capacitors
Stacked Metallized PPS Film Chip Capacitor
Type: ECHU(X)
Stacked metallized PPS film as dielectric with simple
mold-less construction
IFeatures
✕
Small in size (minimum size 1.6 mm 0.8 mm)
85 ˚C, 85 %RH, W.V. 1.0 for 500 hours
For reflow soldering
RoHS directive compliant
•
✕
•
•
•
IRecommended Applications
Time-constant
Filtering
Oscillation and resonance
•
•
•
IExplanation of Part Numbers
1
2
3
4
5
6
7
8
9
10
11
12
E
C
H
U
X
Cap. Tol. Suffix
Product code
Dielectric &
construction
Rated voltage
Capacitance
Suffix
01 10 VDC
1C 16 VDC
1H 50 VDC
G
J
2 %
5 %
5
Tape width
Reel diameter
8 mm
size ø180 mm
12 mm
size ø330 mm
❈
Tape width 8 mm
and diameter
ø330 mm reel is
prepared.
9
ISpecifications
Category temp. range
(Including temperature-rise on unit surface)
-55 ℃ to +125 ℃
10 VDC,16 VDC,50 VDC
Rated voltage
(50 VDC: 0.12 µF or more: Derating or rated voltage by 1.25 % / ℃at more than 105 ℃)
0.00010 µF to 0.22 µF (E12)
Capacitance range
Capacitance tolerance
Withstand voltage
±2 %(G), ±5 %(J)
✕
Between terminals : Rated volt. (VDC) 150 % 60 s
Dissipation factor (tan )
tanδ≦0.6 % (20 ℃, 1 kHz)
10 VDC:IR≧3000 MΩ (20 ℃, 10 VDC, 60 s)
16 VDC:IR≧3000 MΩ (20 ℃, 10 VDC, 60 s)
50 VDC:IR≧3000 MΩ (20 ℃, 50 VDC, 60 s)
Insulation resistance (IR)
Soldering conditions
Reflow soldering : 260 ˚C max. and 95 sec max. at more than 220 ˚C (Temp. at cap. surface)
❈ Please consult us for flow soldering
❈
In case of applying voltage in alternating current (50 Hz or 60 Hz sine wave) to a capacitor with DC rated voltage, please
refer to the page of “Permissible voltage (R.M.S) in alternating current corresponding to DC rated voltage”.
IConstruction
IDimensions in mm (not to scale)
saize
code
L
W
H
e
g
K1
J1
1.6 0.8
0.7 0.35 ≧0.4
2.0 1.25 0.9 0.45 ≧0.6
2.0 1.25 1.1 0.45 ≧0.6
J2
H1
H2
H3
G1
G2
G3
E1
E2
D1
D3
D4
3.2 1.6
3.2 1.6
3.2 1.6
3.2 2.5
3.2 2.5
3.2 2.5
4.8 3.3
4.8 3.3
6.0 4.1
6.0 4.1
6.0 4.1
0.9 0.65 ≧1.0
1.1 0.65 ≧1.0
1.5 0.65 ≧1.0
1.1 0.65 ≧1.0
1.5 0.65 ≧1.0
2.1 0.65 ≧1.0
1.5 0.80 ≧2.0
2.1 0.80 ≧2.0
1.9 0.80 ≧2.0
2.5 0.80 ≧2.0
2.8 0.80 ≧2.0
Design, Specifications are subject to change without notice.
Ask factory for technical specifications before purchase and/or use.
Whenever a doubt about safety arises from this product, please inform us immediately for technical consultation without fail.