DG211
Absolute Maximum Ratings
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44V
Thermal Information
Thermal Resistance (Typical, Note 3)
PDIP Package* . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150°C
Maximum Storage Temperature Range. . . . . . . . . . .-65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
(SOIC - Lead Tips Only)
θ
JA
(°C/W)
100
120
V
V
V
V
to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V- to V+
IN
L
S
S
to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 25V
or V to V+. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to -36V
D
D
or V to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 36V
V+ to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25V
V- to Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -25V
Current, any Terminal Except S or D . . . . . . . . . . . . . . . . . . . . 30mA
Continuous Current, S or D . . . . . . . . . . . . . . . . . . . . . . . . . . . 20mA
Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle Max) . . . . . 70mA
*Pb-free PDIPs can be used for through hole wave solder
processing only. They are not intended for use in Reflow solder
processing applications.
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
3. θ is measured with the component mounted on an evaluation PC board in free air.
JA
Electrical Specifications V+ = +15V, V- = -15V, V = +5V, GND, T = 25°C
L
A
(NOTE 4) (NOTE 5)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
Turn-OFF Time,
See Figure 1
S
-
460
-
ns
ON
V
= 10V, R = 1kΩ, C = 35pF
L L
t
t
-
-
-
-
-
-
-
360
450
70
-90
5
-
-
-
-
-
-
-
ns
ns
OFF1
OFF2
OFF Isolation, OIRR (Note 7)
V
= 5V, R = 1kΩ, C = 15pF, V = 1V ,
RMS
dB
dB
pF
pF
pF
IN
L
L
S
f = 100kHz
Crosstalk (Channel to Channel), CCRR
Source OFF Capacitance, C
V
= V = 0V, V = 5V, f = 1MHz
S(OFF)
D
S
IN
Drain OFF Capacitance, C
5
D(OFF)
Channel ON Capacitance, C
+ C
S(ON)
16
D(ON)
DIGITAL INPUT CHARACTERISTICS
Input Current with Voltage High, I
V
V
V
= 2.4V
= 15V
= 0V
-1.0
-
-0.0004
0.003
-
1.0
-
µA
µA
µA
IH
IN
IN
IN
Input Current with Voltage Low, I
-1.0
-0.0004
IL
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
-15
-
15
175
5.0
-
V
ANALOG
Drain-Source ON Resistance, r
V
V
= ±10V, I = 1mA, V = 0.8V
-
-
150
Ω
DS(ON)
D
S
IN
Source OFF Leakage Current, I
= 2.4V
= 0.8V
V
= 14V, V = -14V
0.01
-0.02
0.01
-0.02
0.1
nA
nA
nA
nA
nA
nA
S(OFF)
D(OFF)
D(ON)
IN
S
S
S
S
S
S
D
V
V
V
V
V
= -14V, V = 14V
-5.0
-
D
Drain OFF Leakage Current, I
= -14V, V = 14V
5.0
-
D
= 14V, V = -14V
-5.0
-
D
Drain ON Leakage Current, I
(Note 6)
V
= V = 14V
5.0
-
IN
D
= V = -14V
-5.0
-0.15
D
FN3118.4
3
December 21, 2005