5秒后页面跳转
捷配首页

Datasheet > DAC7614UBG4
DAC7614UBG4 PDF预览

DAC7614UBG4

更新时间： 2024-02-13 23:03:56
品牌 Logo 应用领域
德州仪器 - TI 光电二极管转换器数模转换器
页数 文件大小 规格书
17页 529K
描述
四路串行输入 12 位电压输出数模转换器 | DW | 16 | -40 to 85

阅读下载

中文翻译

获取价格

DAC7614UBG4 技术参数

是否无铅： 不含铅是否Rohs认证： 符合
生命周期：Active零件包装代码：SOIC
包装说明：SOP, SOP16,.4针数：16
Reach Compliance Code：compliantECCN代码：EAR99
HTS代码：8542.39.00.01Factory Lead Time：6 weeks
风险等级：1.78最大模拟输出电压：2.5 V
最小模拟输出电压：-2.5 V转换器类型：D/A CONVERTER
输入位码：BINARY输入格式：SERIAL
JESD-30 代码：R-PDSO-G16JESD-609代码：e4
长度：10.3 mm最大线性误差 (EL)：0.0244%
湿度敏感等级：3标称负供电电压：-5 V
位数：12功能数量：1
端子数量：16最高工作温度：85 °C
最低工作温度：-40 °C封装主体材料：PLASTIC/EPOXY
封装代码：SOP封装等效代码：SOP16,.4
封装形状：RECTANGULAR封装形式：SMALL OUTLINE
峰值回流温度（摄氏度）：260电源：5/+-5 V
认证状态：Not Qualified采样速率：0.089 MHz
座面最大高度：2.65 mm最大稳定时间：10 µs
标称安定时间 (tstl)：10 µs子类别：Other Converters
最大压摆率：1.9 mA标称供电电压：5 V
表面贴装：YES技术：CMOS
温度等级：INDUSTRIAL端子面层：Nickel/Palladium/Gold (Ni/Pd/Au)
端子形式：GULL WING端子节距：1.27 mm
端子位置：DUAL处于峰值回流温度下的最长时间：NOT SPECIFIED
宽度：7.5 mm

DAC7614UBG4 数据手册

 浏览型号DAC7614UBG4的Datasheet PDF文件第9页浏览型号DAC7614UBG4的Datasheet PDF文件第10页浏览型号DAC7614UBG4的Datasheet PDF文件第11页浏览型号DAC7614UBG4的Datasheet PDF文件第13页浏览型号DAC7614UBG4的Datasheet PDF文件第14页浏览型号DAC7614UBG4的Datasheet PDF文件第15页 
The power applied to VDD (as well as VSS, if not grounded)  
should be well regulated and low noise. Switching power  
supplies and DC/DC converters will often have high-fre-  
quency glitches or spikes riding on the output voltage. In  
addition, digital components can create similar high-fre-  
quency spikes as their internal logic switches states. This  
noise can easily couple into the DAC output voltage through  
various paths between the power connections and analog  
output.  
LAYOUT  
A precision analog component requires careful layout, ad-  
equate bypassing, and clean, well-regulated power supplies.  
As the DAC7614 offers single-supply operation, it will often  
be used in close proximity with digital logic, microcontrollers,  
microprocessors, and digital signal processors. The more  
digital logic present in the design and the higher the switch-  
ing speed, the more difficult it will be to achieve good  
performance from the converter.  
As with the GND connection, VDD should be connected to  
a +5V power supply plane or trace that is separate from the  
connection for digital logic until they are connected at the  
power entry point. In addition, the 1µF to 10µF and 0.1µF  
capacitors shown in Figure 4 are strongly recommended. In  
some situations, additional bypassing may be required, such  
as a 100µF electrolytic capacitor or even a “Pi” filter made  
up of inductors and capacitors—all designed to essentially  
lowpass filter the +5V supply, removing the high frequency  
noise (see Figure 4).  
Because the DAC7614 has a single ground pin, all return  
currents, including digital and analog return currents, must  
flow through the GND pin. Ideally, GND would be con-  
nected directly to an analog ground plane. This plane would  
be separate from the ground connection for the digital  
components until they were connected at the power entry  
point of the system (see Figure 4).  
Digital Circuits  
+5V  
+5V  
Power Supply  
Ground  
+5V  
DAC7614  
Ground  
VDD  
100µF  
+
+
1µF to  
10µF  
0.1µF  
GND  
Optional  
Other  
Analog  
Components  
FIGURE 4. Suggested Power and Ground Connections for a DAC7614 Sharing a +5V Supply with a Digital System.  
®
12  
DAC7614  
1...9101112131415...17

中文翻译

下载PDF

DAC7614UBG4 替代型号

型号 品牌 替代类型 描述 数据表
DAC7614UB/1K TI

完全替代

 		Quad, Serial Input, 12-Bit, Voltage Output
DAC7614UB TI

完全替代

 		Quad, Serial Input, 12-Bit, Voltage Output

与DAC7614UBG4相关器件

型号 品牌 描述 获取价格 数据表
DAC7614UG4 TI 四路串行输入 12 位电压输出数模转换器 | DW | 16 | -40 to 85

获取价格
DAC7615 BB Quad, Serial Input, 12-Bit, Voltage Output DIGITAL-TO-ANALOG CONVERTER

获取价格
DAC7615 TI 四路串行输入 12 位电压输出数模转换器

获取价格
DAC7615E BB Quad, Serial Input, 12-Bit, Voltage Output DIGITAL-TO-ANALOG CONVERTER

获取价格
DAC7615E TI Quad, Serial Input, 12-Bit, Voltage Output

获取价格
DAC7615E/1K TI Quad, Serial Input, 12-Bit, Voltage Output

获取价格

与DAC7614UBG4相关文章

您还可以找


热门产品
PCB打样/小批量
铝基板
BOM智能配单
PCBA制造
钣金
精密CNC
模具注塑
薄膜开关
精选活动
PCBA打样特惠
四六层板品质升级
铝基板品质升级
一体化电子制造
DFM下载
服务支持
企业认证
产品展示
工厂展示
工艺能力
积分商城
关于捷配
捷配简介
企业文化
公司动态
人才招聘
联系我们
帮助中心
下单流程
付款流程
开票流程
常见问题
全球PCB制造服务专线 400-613-0088

工作时间：9:00-21:00

CEO邮箱：ceo@jiepei.com

投诉邮箱：tousu@jiepei.com

捷配网-微信公众号 微信公众号
捷配网-微信公众号 抖音公众号
资质认证：
合作快递：
支付方式：
Copyright © 2024 Jiepei.com Inc. All Rights Reserved. 版权所有:杭州捷配信息科技有限公司 浙公网安备 33010502006866号 浙ICP备10014259号-119 营业执照ICP证