5x7mm Surface Mount
High Precision
TCXO
In Stock at Digi-Key
Description
Features
The Connor-Winfield’s D75AS
is a 5x7mm Surface Mount
Model D75AS
TCXO
3.3V Operation
Clipped Sinwave Output
Frequency Stability: 0.25ppm
Temperature Range: 0 to 70°C
Low Jitter <1pS RMS
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630-851-4722
Fax: 630-851-5040
Temperature Compensated
Crystal Controlled Oscillators
(TCXO) with a clipped
sinewave output. Through the use of
Analog Temperature Compensation,
the D75AS is capable of holding sub
0.25-ppm stabilities over the 0 to
70°C temperature range.
www.conwin.com
Tri-State Enable/Disable Function
5x7mm Surface Mount Package
Tape and Reel Packaging
RoHS Compliant / Lead Free
US Headquarters
630-851-4722:
European Headquarters:
+353-61-472221
Absolute Maximum Ratings
Parameter
Minimum
-55
Nominal
Maximum
85
Units
°C
Note
Storage Temperature
-
-
-
Supply Voltage
Input Voltage
(Vcc)
(Fo)
-0.5
6.0
Vdc
Vdc
-0.5
Vcc+0.5
Operating Specifications
Parameter
Minimum
Nominal
Maximum
Units
MHz
Note
Frequencies Available
20.0
Frequency Calibration @ 25 C
Frequency Stability [ (Fmax – Fmin)/2.Fo]
Supply Voltage Variation (Vcc 5%)
Load Coefficient ( 5%)
-1.00
-
1.00
0.25
0.025
0.025
0.40
1.00
4.60
70
ppm
1
2
-0.25
-
ppm
-0.025
-
ppm
-0.025
-
-
ppm
Static Temperature Hysteresis
Frequency shift after reflow soldering
Total Frequency Tolerance
Temperature Range
-
ppm
Absolute, 3
-1.00
-
ppm
4
5
-4.60
-
ppm
0
-
C
Supply Voltage
(Vcc)
(Icc)
3.135
3.3
-
3.465
10
Vdc
Supply Current
-
-
-
-
-
-
-
mA
Period Jitter
3
5
ps rms
ps rms
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
Phase Jitter (BW=12kHz to 20MHz)
SSB Phase Noise at 10Hz offset
SSB Phase Noise at 100Hz offset
SSB Phase Noise at 1KHz offset
SSB Phase Noise at >10KHz offset
0.5
-80
-110
-135
-150
1
Input Characteristics For Enable / Disable Function (Pin 8)
Parameter
Minimum
Nominal
Maximum
-
Units
Vdc
Note
Enable Voltage (High) or open circuit
Disable Voltage (Low) Output Disabled
(Vih)
(Vil)
70%Vcc
-
-
-
6
30%Vcc
Vdc
Clipped Sinewave Output Characteristics
Parameter
Minimum
Nominal
Maximum
Units
V pk-pk
Ohms
pF
Note
Output Voltage
1.00
-
-
-
-
7
Output Load Resistance
Output Load Capacitance
-
-
10K
10
8
Note:
1) Initial calibration @ 25 C. Specifications at time of shipment after 48 hours of operation
2) Frequency stability vs. change in temperature.
3) Frequency change after reciprocal temperature ramped over the operating range. Frequency measured before
and after at 25°C.
4) Within two hours after reflow.
5) Inclusive of calibration @ 25 C, frequency vs. change in temperature, change in supply voltage ( 5%), load
change ( 5%), reflow soldering process and 20 years aging, referenced to Fo.
6) Leave Pad 8 unconnected if enable / disable function is not required. When tri-stated, the output stage is
disabled but the oscillator and compensation circuit are still active (current consumption < 1 mA).
7) Output is AC coupled.
Bulletin
Page
Tx243
1 of 2
00
8) For best performance it is recommended that the circuit connected to this output should have an equivalent
input capacitance of 10pF.
Revision
Date
21 Oct 2008
Specifications subject to change without notice. All dimensions in inches. © Copyright 2008 The Connor-Winfield Corporation